Extron electronic Switch YCS SW6 MX User Manual

User’s Manual  
YCS SW6 MX  
Y/C Separator Switcher  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
USA  
714.491.1500  
Fax 714.491.1517  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort  
The Netherlands  
+31.33.453.4040  
Fax +31.33.453.4050  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Building  
Singapore 368363  
+65.6383.4400  
Fax +65.6383.4664  
Extron Electronics, Japan  
Daisan DMJ Building 6F  
3-9-1 Kudan Minami  
Chiyoda-ku, Tokyo 102-0074 Japan  
+81.3.3511.7655  
68-314-01  
Printed in the USA  
Fax +81.3.3511.7656  
© 2002 Extron Electronics. All rights reserved.  
 
Table of Contents  
Chapter 1 • Introduction.......................................................... 1-1  
Features ...................................................................................... 1-2  
Chapter 2 • Installation and Operation ........................ 2-1  
Installation................................................................................ 2-2  
Rear panel features ............................................................... 2-2  
Installation procedure ........................................................... 2-3  
Mounting the switcher ...................................................... 2-3  
Installing the rubber feet .................................................. 2-4  
Cabling the switcher .......................................................... 2-4  
Attaching remote control devices ........................................ 2-6  
Installing an IR 20 infrared remote control ....................... 2-6  
Operation ................................................................................... 2-6  
Front panel features .............................................................. 2-7  
Selecting an input.................................................................. 2-7  
Chapter 3 • Serial Communication................................... 3-1  
RS-232 Programmer’s Guide............................................. 3-2  
Switcher-initiated messages.................................................. 3-2  
Switcher error responses ....................................................... 3-3  
Using the command/response table ..................................... 3-3  
Command/response table ..................................................... 3-4  
Universal SW Control Program ....................................... 3-5  
Installing the software .......................................................... 3-5  
Using the software ................................................................ 3-5  
Remote Contact Closure Operation ............................. 3-6  
Appendix • Reference Information................................. A-1  
Specifications ......................................................................... A-2  
Part Numbers .......................................................................... A-3  
Related part numbers........................................................... A-3  
Super high resolution cable ................................................. A-4  
S-video cable ......................................................................... A-5  
68-314-01 Rev. D  
Printed in the USA  
05 02  
YCS SW6 MX • Table of Contents  
i
 
Table of Contents, cont’d  
YCS SW6 MX  
Chapter One  
1
Introduction  
Features  
YCS SW6 MX • Table of Contents  
ii  
 
Introduction  
The Extron YCS SW6 MX is a video decoder/encoder/switcher  
with both composite and S-video outputs. It separates input  
composite video signals into their YC (luminance and  
YCS SW6 MX  
chrominance) components (S-video), or it combines input  
S-video YC signals into composite video format. Both formats  
are available for output regardless of the selected input type.  
Six switchable inputs are available. Inputs 1 – 4 use either BNC  
or mini-DIN connectors for either composite video or S-video.  
Inputs 5 and 6 use BNC connectors for composite video.  
Switching occurs during the vertical blanking interval of the  
video signal.  
Features  
Video formats — The switcher can be configured to operate in  
either NTSC or PAL mode.  
Inputs — Six inputs are provided. Four can be used as either  
composite video or S-video, and two are dedicated to  
composite video.  
Chapter Two  
Built-in YC separator — Composite video can be converted to  
S-video.  
Built-in YC combiner — S-video can be converted to composite  
2
video.  
Dual buffered outputs — Two outputs are provided. One is for  
composite video, and one is for S-video. These outputs  
function simultaneously.  
Multiple control methods — You can select an input by using  
Installation and Operation  
any of the following:  
• Front panel control buttons  
• Extron’s control program for Windows  
Installation  
Operation  
• RS-232 command using Extron’s Simple Instruction Set™  
(SIS™)  
• Third-party contact closure remote control  
• Infrared remote control  
Power supply — The switcher includes a 100VAC to 240VAC,  
50/60 Hz, internal, auto-switchable power supply.  
Rack mountable — The switcher can be rack mounted on one  
side of an optional 1U rack shelf (Extron part number  
60-190-01).  
YCS SW6 MX • Introduction  
1-2  
 
Installation and Operation  
5 — Not used  
6 — Not used  
7 — Not used  
Installation  
Rear panel features  
2
4
1
3
8 — Video standard  
Up — Video standard is NTSC.  
Down — Video standard is PAL.  
Input 4-pin mini-DIN connectors — Four 4-pin mini-DIN  
7
female connectors for S-video input devices.  
6
5
7
Figure 1 — YCS SW6 MX rear panel  
Installation procedure  
To install a YCS SW6 MX switcher, perform the following steps:  
AC power connector — One standard AC power connector  
attaches the switcher to any power source from 100VAC to  
240VAC, operating at 50 or 60 Hz.  
1
If desired, mount the switcher in a rack (see “Mounting  
the switcher”, below). Otherwise, install the rubber feet  
(see “Installing the rubber feet” on page 2-4).  
1
Input BNC connectors — Six BNC female connectors for  
composite video input devices.  
2
3
4
Turn off power to the input and output devices ,and  
unplug the power cables from them.  
2
3
4
5
Output BNC connector — One BNC female connector for a  
composite video output device.  
Attach the switcher to the input devices and output  
devices (see “Cabling” on page 2-4).  
Remote connector — One 9-pin D female RS-232 connector that  
allows you to attach a host/computer, contact closure, or  
infrared remote control device to the switcher.  
Set the DIP switches on the switcher (see item 6 on  
page 2-2).  
Output 4-pin mini-DIN connector — One 4-pin mini-DIN  
female connector for an S-video output device.  
If desired, attach an optional or third-party remote control  
5
6
device (see “Attaching remote control devices” on page 2-  
5).  
Switch module — DIP switch module that selects between  
composite video and S-video for inputs 1 – 4, and selects  
between NTSC and PAL.  
Plug the switcher, input devices, and output devices into a  
grounded AC source, and turn on the input and output  
devices..  
6
7
1 — Input 1  
The image from the selected input device should appear  
on the output device. If it does not, double-check steps 3 –  
5, and make adjustments as needed.  
Up — Input 1 is composite video.  
Down — Input 1 is S-video.  
2 — Input 2  
Mounting the switcher  
Up — Input 2 is composite video.  
Down — Input 2 is S-video.  
The YCS SW6 MX switcher can be rack mounted on one side of  
an optional 19”, 1U Universal Rack Shelf (Extron part number  
60-190-01). To rack mount the switcher, do the following:  
3 — Input 3  
Up — Input 3 is composite video.  
Down — Input 3 is S-video.  
1.  
If feet were previously installed on the bottom of the  
switcher, remove them.  
4 — Input 4  
2.  
Mount the switcher on the rack shelf as shown in figure 2.  
Attach two 4-40 x 1/8 screws in opposite (diagonal)  
corners to secure the switcher to the shelf.  
Up — Input 4 is composite video.  
Down — Input 4 is S-video.  
YCS SW6 MX • Installation and Operation  
2-2  
YCS SW6 MX • Installation and Operation  
2-3  
 
Installation and Operation, cont’d  
Composite  
S-video  
Figure 3 — Input and output cabling  
Video Camera  
RS-232 Control  
Monitor  
YCS SW6 MX  
Figure 2 — Mounting the switcher  
3.  
If a false front panel is required, mount it on the shelf  
using the front two holes.  
Laserdisc Player  
VCR  
Installing the rubber feet  
Cable Box  
DSS Receiver  
DVD Players  
VCR  
The switcher ships with four uninstalled rubber feet. Install the  
rubber feet only if you are not rack-mounting the switcher. To  
install the rubber feet, do the following:  
Figure 4 — YCS SW6 MX application diagram  
1.  
Turn the switcher upside down and place it on a flat  
surface.  
2.  
3.  
Remove the protective backing from a rubber foot.  
Video Camera  
Place the rubber foot on one corner of the switcher’s  
bottom surface, and press it into place.  
4.  
5.  
Repeat steps 2 and 3 to install a rubber foot on each of the  
remaining corners of the switcher.  
Turn the switcher right side up and place it in the desired  
location.  
RS-232 Control  
Cabling the switcher  
Preview  
Monitor  
YCS SW6 MX  
Use high resolution cable for all video input and output  
connections. See page A-4 for Extron’s high-resolution cables.  
To cable the YCS SW6 MX switcher, connect the input and  
output devices to the switcher using figures 3, 4, and 5 as  
a guide.  
X
0G  
10 TER  
C
ER  
V
S
N
V
O
N
C
SCA  
L
NA  
SIGCK  
D
EO LO  
K
C
S-VI  
LO  
Z
EN  
SUB  
G
HOR  
E
G
ST  
K
S
PHA  
R
GB  
IN  
R
ER  
VE  
B
U
O
C
L
T
L
ASE  
PH  
FI  
RT  
I
I
RZ  
I
HO  
I
I
I
OM  
ER  
ER  
UND  
ZO  
N
O
V
A
/P  
G
IN  
R
TE  
EN  
C
M
AX  
MIN  
ZE  
EE  
FR  
Extron  
VSC 100GX  
Document  
Camera  
Videoconferencing  
System  
Laptop  
DVD Players  
VCR  
Figure 5 — Video conferencing application  
YCS SW6 MX • Installation and Operation  
2-4  
YCS SW6 MX • Installation and Operation  
2-5  
 
Installation and Operation, cont’d  
3.  
Plug the IR detector’s male plug into the IR 20 adapter’s  
RJ-11 female connector.  
Attaching remote control devices  
The remote connector provides a way to control the switcher by  
using contact closure devices such as the following:  
4.  
5.  
Connect the 9VDC power supply to the IR 20 adapter.  
Position the IR detector (limited by its cable length) in the  
best position to receive infrared light from the IR 20 hand-  
held remote control.  
• Extron’s IR 20 infrared remote control (see “Installing an IR 20  
infrared remote control” below).  
• Remote contact closure (see “Remote Contact Closure  
Operation” on page 3-6).  
Operation  
• RS-232 port and a host computer (see “Serial Communication”  
on page 3-2).  
Front panel features  
Installing an IR 20 infrared remote control  
1
2
The IR 20 remote control system includes the following  
components:  
• IR 20 remote control (hand-held remote control unit)  
• IR detector with 6-foot (1.8 meter) cable and RJ-11 connector  
• IR 20 adapter with 3-foot (0.9 meter) cable and RS-232 T  
connector  
3
Figure 7 — Front panel features  
• External 9VDC power supply for adapter.  
To install an IR 20 infrared remote control, do the following:  
Power LED — Lights to indicate that power is supplied to the  
switcher.  
1
1.  
Attach the 9-pin T plug on the IR 20 adapter to the remote  
connector on the rear panel of the switcher (figure 6).  
Input selection LEDs — Light to indicate the active input.  
2
3
Input selection buttons — Allow you to select the input to be  
1
2
3
4
5
6
7
8
displayed.  
YCS SW6 MX  
PC Computer  
Selecting an input  
RS-232  
T Connector  
The YCS SW6 MX switcher is a video decoder/encoder/  
switcher with both composite and S-video outputs. It separates  
composite video into S-video format, or it combines S-video  
(YC) input signals into composite video format. Both formats  
are available as outputs, regardless of the selected input type.  
IR Detector  
To select an input using the front panel buttons, press the button  
for the desired input. The LED for the selected input turns on.  
IR-20  
IR 20 Remote Control  
Adapter  
When a new input is selected, switching does not occur until the  
next vertical blanking interval of the current input signal. The  
output is then switched to the new input.  
IR 20  
Remote Control  
Figure 6 — Installing the IR 20 infrared remote  
control  
2.  
If a host RS-232 device is also being attached, connect its  
RS-232 plug to the unused side of the adapter’s RS-232  
T connector.  
YCS SW6 MX • Installation and Operation  
2-6  
YCS SW6 MX • Installation and Operation  
2-7  
 
Installation and Operation, cont’d  
YCS SW6 MX  
Chapter 3  
3
Serial Communication  
RS-232 Programmer’s Guide  
Universal SW Control Program  
Remote Contact Closure Operation  
YCS SW6 MX • Installation and Operation  
2-8  
 
Serial Communication  
The YCS SW6 MX switcher can be controlled by a host computer  
Switcher error responses  
or other control device via an RS-232 connection with a protocol  
of 9600 baud, 1 stop bit, no parity, and no flow control. The  
control device can use either Extron’s Simple Instruction Set  
(SIS) or the graphical control program for Windows.  
When the switcher receives a valid SIS command, it executes the  
command and sends a response to the host device. If the  
switcher is unable to execute the command because the  
command is invalid or it contains invalid parameters, the  
switcher returns an error response to the host. The error  
response codes and their descriptions are as follows:  
5
1
The rear panel RS-232 9-pin D connector has the  
following pin assignments:  
9
6
DB9 Pin Locations  
Female  
E01 — Invalid input channel number (out of range)  
E10 — Invalid command  
Pin  
Description  
E13 — Invalid value (out of range)  
1
2
3
4
5
6
7
8
9
Input #1  
Transmit data  
Receive data  
Input #2  
Ground  
Input #3  
Input #4  
Input #5  
Input #6  
Using the command/response table  
The table on page 3-4 lists the commands that the switcher  
recognizes as valid, the responses that are returned to the host, a  
description of the command’s function or the results of  
executing the command, and an example of each command.  
Lower case characters are acceptable in the command field only  
where indicated.  
Symbol definitions are shown at the beginning of the table. An  
ASCII to HEX conversion table is provided in figure 8.  
RS-232 Programmer’s Guide  
ASCII to HEX Conversion Table  
SIS commands consist of one or more characters per field. No  
special characters are required to begin or end a command  
sequence. When the switcher determines that a command is  
valid, it executes the command and sends a response to the host  
device. All responses from the switcher to the host end with a  
carriage return and a line feed (CR/LF = ), which signals the  
end of the response character string. A string is one or more  
characters.  
Switcher-initiated messages  
When a local event such as an input selection occurs, the  
switcher responds by sending a message to the host. No  
response is required from the host. The switcher-initiated  
messages are listed below (underlined).  
Figure 8 — ASCII-to-HEX conversion table  
(C)COPYRIGHT 1997, EXTRON ELECTRONICS YCS SW6 MX,  
Vx.xx  
The switcher displays the copyright message when it first  
powers on. Vx.xx is the firmware version number.  
YCS SW6 MX • Serial Communication  
3-2  
YCS SW6 MX • Serial Communication  
3-3  
 
Serial Communication, cont’d  
Symbol definitions  
= CR/LF (carriage return/line feed)  
= Space  
X1 = Input number 0 – 6 (0 = Muted output)  
X2 = Software version x.xx  
Universal SW Control Program  
The Universal SW Control Program, Extron part number  
29-031-01, which ships with the YCS SW6 MX switcher, is  
compatible with Windows 3.1, 3.11, 95/98, and NT. It provides  
remote control of input selection.  
X3 = Format  
Installing the software  
0 = Muted output, 5 = NTSC/composite video,  
6 = NTSC/S-video, 7 = PAL/composite video,  
8 = PAL/S-video  
The Universal SW Control Program is contained on a single 3.5”  
diskette, and it can run from the floppy drive. However, it is  
usually more convenient to load and run the program from the  
hard drive.  
Command/response table  
To install the software from the floppy disk onto the hard drive,  
run SETUP.EXE from the floppy disk, and follow the  
instructions that appear on the screen. The program occupies  
approximately 1 MB (megabyte) of hard disk space.  
Command description  
Select input channel  
ASCII  
Response  
X1  
X1  
X1  
Select input channel  
&
C
Example:  
5&  
C5  
X1  
X1  
Select input channel  
Example:  
(audio)*  
!
C
X1  
By default, the Windows installation creates a C:\UNIVSW  
directory, and it places two icons (Universal Switcher Control  
Pgm and Universal Switcher Help) into a group or folder  
named “Extron Electronics”.  
2!  
C2  
* If an audio/video switcher is chained to the RS-232 port of the YCS SW6 MX,  
use this command to break the audio signal away from the video signal.  
Request information  
Using the software  
X1  
X3  
X2  
I/i  
I
V
•T •QVER •M6  
Example:  
V2•T6•QVER1.23•M6  
To run the software, do the following:  
Current input - input 2, NTSC/S-video; software version = 1.23; and maximum  
number of inputs = 6.  
1.  
Double-click on the Universal Switcher Control Pgm icon  
in the Extron Electronics group or folder.  
Request part number  
N/n  
N
Nxx-xxx-xx  
N60-224-01  
The Comm menu appears on the screen.  
Example:  
Query software version  
Q/q  
Q
QVER X2  
QVER1.23  
Example:  
2.  
3.  
Click on the comm port that is connected to the switcher’s  
RS-232 port.  
The Universal SW Control Program window appears  
(figure 9, on the next page). It displays the current input  
selection.  
Using normal Windows controls, you can perform the  
same adjustments as from the front panel.  
YCS SW6 MX • Serial Communication  
3-4  
YCS SW6 MX • Serial Communication  
3-5  
 
Serial Communication, cont’d  
YCS SW6 MX  
Figure 9 — Universal SW Control Program  
For more information about program features, you can access  
the Help program in any of the following ways:  
• From the Extron Electronics program folder or group, double-  
click on the Universal Switcher Help icon.  
Appendix  
• From within the Universal SW Control Program, click on the  
Help menu on the main screen.  
A
• From within the Universal SW Control Program, press the F1  
key.  
Remote Contact Closure Operation  
Reference Information  
The RS-232 connector provides a way to control the switcher  
from a remote contact closure device. This is made possible by  
using pins that are not normally used by the RS-232 interface.  
The contact closure pin assignments are shown in the table on  
page 3-2.  
Specifications  
Part Numbers  
To select a different input number through the RS-232 connector,  
momentarily short the pin for the desired input number to the  
signal ground (pin 5). To force one of the inputs to be selected,  
leave the short to signal ground in place. This overrides any  
front panel input selection.  
Momentary contact is 250 – 500 milliseconds.  
Avoid contact with pins 2 and 3, which are used  
with the RS-232 interface. Shorting these pins to  
ground or to other pins on the RS-232 connector  
could damage internal circuits.  
YCS SW6 MX • Serial Communication  
3-6  
 
Reference Information  
Rack mount................................... Yes, with optional rack shelf, part  
#60-190-01  
Enclosure type.............................. Metal  
Enclosure dimensions ................. 1.75" H x 8.75" W x 9.5" D (1U high, 1/2  
rack width)  
Video  
Gain ............................................... Unity  
Bandwidth .................................... 30 MHz (-3dB)  
Crosstalk ....................................... -60dB @ 3.58 MHz  
4.4 cm H x 22.2 cm W x 24.1 cm D  
(Depth excludes connectors.)  
Product weight............................. 2.8 lbs (1.3 kg)  
Shipping weight .......................... 5 lbs (2.3 kg)  
Vibration ....................................... ISTA/NSTA 1A in carton (International  
Safe Transit Association)  
Video input  
Number/signal type ................... 4 NTSC/PAL S-video  
6 NTSC/PAL composite video  
Connectors .................................... 6 BNC female  
4 4-pin mini-DIN female  
Impedance .................................... 75 ohms  
Return loss .................................... -30dB @ 5 MHz  
Listings .......................................... UL, CUL  
Compliances ................................. CE, FCC Class A  
MTBF ............................................. 30,000 hours  
Warranty ....................................... 3 years parts and labor  
Video output  
Number/signal type ................... 1 NTSC/PAL S-video and composite  
video  
Specifications are subject to change without notice.  
Connectors .................................... 1 BNC female  
1 4-pin mini-DIN female  
Minimum/maximum levels ...... Analog ....... 0.3V to 1.5V p-p  
Impedance .................................... 75 ohms  
Return loss .................................... -30dB @ 5 MHz  
Part Numbers  
Related part numbers  
Description  
Part number  
DC offset ....................................... 5mV maximum with input at 0 offset  
Switching type ............................. Vertical interval  
YCS SW6 MX  
60-224-01  
60-190-01  
70-036-02  
70-036-03  
68-314-01  
26-345-01  
10-264-01  
1U, 19” universal rack shelf  
IR 20 remote control system (US/Canada)  
IR 20 remote control system (world)  
YCS SW6 MX User’s Manual  
RCA-6’ (1.8 m) RCA male to male cable  
BNCM-RCAF adapter  
Sync  
Standards ...................................... NTSC, PAL  
Control/remote — Y/C separator/switcher  
Serial control port ........................ RS-232, 9-pin D female connector  
Baud rate and protocol ............... 9600, 8-bit, 1 stop bit, no parity  
Serial control pin configurations. 2 = TX, 3 = RX, 5 = GND  
IR controller module ................... Extron IR 20  
Program control ........................... Extron’s control program for Windows®  
Extron’s Simple Instruction Set™ – SIS™  
General  
Power............................................. 100VAC to 240VAC, 50/60 Hz, 12 watts,  
internal, auto-switchable  
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /  
10% to 90%, non-condensing  
Operating +32° to +122°F (0° to +50°C) /  
10% to 90%, non-condensing  
YCS SW6 MX • Reference Information  
A-2  
YCS SW6 MX • Reference Information  
A-3  
 
Reference Information, cont’d  
Super high resolution cable  
Description  
Part number  
Single conductor  
SHR1-3’  
26-383-01  
26-383-12  
26-383-07  
26-383-04  
26-383-05  
26-383-06  
26-383-03  
26-383-08  
26-383-09  
26-383-10  
26-383-11  
SHR1-6’  
SHR1-12’  
SHR1-25’  
SHR1-50’  
SHR1-75’  
SHR1-100’  
SHR1-150’  
SHR1-200’  
SHR1-250’  
SHR1-300’  
S-video cable  
Description  
Part number  
SVHS 6‘  
26-316-02  
26-316-03  
26-316-01  
26-316-04  
26-316-05  
26-316-06  
26-316-07  
SVHS 12‘  
SVHS 20‘  
SVHS 30‘  
SVHS 50‘  
SVHS 75‘  
SVHS 100‘  
SVHSM-BNCF S-video male to  
two male BNCs, 8”  
26-353-01  
YCS SW6 MX • Reference Information  
A-4  
YCS SW6 MX • Reference Information  
A-5  
 
Reference Information, cont’d  
YCS SW6 MX • Reference Information  
A-6  
 

Coleman Camping Equipment 2000001081 User Manual
Cortelco Telephone Colleague User Manual
Cub Cadet Lawn Mower 2146 User Manual
Delta Electronics Power Supply S48SA User Manual
Dixon Lawn Mower RAM 44 968999551 User Manual
Dual CD Player MXD55 User Manual
Dualit Coffee Grinder IB CCG2 A User Manual
Duracraft Humidifier DH 890 User Manual
Ele Cash Register 45 9300 User Manual
GE Monogram Range ZET2PM User Manual