BTV30
INSTALLATION/OWNER'SꢀMANUAL
UniversalꢀBluetooth®ꢀꢀSpeakerphone
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
INTRODUCTION
ControlꢀLocations
G
Visor Clip
LCD
Speaker
Microphone
Earphone Jack
JOG Button
Charging Port
End Button
Hotline Button
Talk Button
DisplayꢀComponents
Bluetooth Connection
Mute
Volume
Bluetooth Signal Strength
Status Display
Call Activation
Battery Meter
2
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
OPERATION
PowerꢀOn
Gently lift the LCD flap to turn the unit on. The LCD will
illuminate, and "HELLO" will appear momentarily in
the display.
Note: After 60 seconds of no activity, the LCD
illumination will turn off and the unit will enter power
save mode. Press any button to exit power save mode.
PowerꢀOff
Gently close the LCD flap to turn the unit off.
BluetoothꢀPairing
1) To pair a Bluetooth enabled mobile phone to the BTV30, press
seconds. "PAIRING" will appear in the display.
for three
2) The unit will broadcast a signal for 60 seconds. To manually exit pairing mode
during this time, press momentarily.
3) Complete the pairing from the Bluetooth menu of the phone by searching
for new devices. Please refer to the phone's instruction manual for further
information on Bluetooth pairing and connections.
4) The phone will display the unit model name (BTV30) and prompt to begin pairing.
5) When prompted, enter the four-digit PIN number (0000).
AutomaticꢀConnection
When the unit is turned on, it will automatically reconnect to the phone to which
it was last connected. If the phone does not connect automatically, press
reconnect. Some phones may not support this feature.
to
Disconnectingꢀ
Disconnect a phone from the BTV30 by using the Bluetooth menu of the phone.
Please refer to the phone's instruction manual for further information.
3
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
OPERATION
MakingꢀaꢀCall
NumberꢀDialing
Select a phone number in one of the following two ways:
• Press JOG to the right to scroll through the last five numbers.
• Press JOG to the left, and follow the prompts to search for a phone book entry.
Refer to page 8 for a detailed explanation of the phone book search function.
Once the desired number is selected, press
to connect the call.
LastꢀNumberꢀRedialing
Press
one time to redial the last outgoing number. If no phone number is
available, a beep will be heard.
VoiceꢀRecognitionꢀDialing
Press and hold
for three seconds to activate voice dialing on the mobile phone.
briefly to cancel.
When the unit beeps, speak the desired name. Press
Note: This feature will only work with phones that support voice dialing.
HotlineꢀDialing
Use the menu to input a hotline number (see page 7 for instructions), which
provides one-touch access to a commonly-called number. Press H (the hotline
button) at any time to dial the programmed number.
ReceivingꢀaꢀCall
The unit will ring and display the phone number of the incoming call. If the call is
from a number stored in the phone book, the caller's name will be displayed on the
LCD. Press
to answer the call.
RejectingꢀaꢀCall
When the unit rings, press
to reject the incoming call.
.
EndingꢀaꢀCall
To end an active call, press
4
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
OPERATION
TransferringꢀaꢀCall
Press
during a phone call to transfer audio between the BTV30 and a phone.
Tip: Transfer audio to the phone before turning the BTV30 off.
CallꢀWaiting
The unit allows two options for answering an incoming call while on an active call:
•
To place the current call on hold and answer an incoming call, press and
hold JOG to the right for two seconds. The unit will beep, and the
incoming call will become active. To return to the original call, press and hold
JOG to the right for two seconds.
•
To end the current call and answer an incoming call, hold JOG to the
left for two seconds until the unit beeps. The incoming call will become active
and the current call will be released.
Volume
To adjust the volume level, press JOG to the left to decrease volume or to the right
to increase volume.
Note: the volume can only be adjusted during a call.
Mute
To mute the microphone during a call, press in on JOG once. To turn off the mute
function, press in on JOG one more time.
Reset
To reset the unit to its factory settings, press and hold
seconds. "RESET" will appear in the display.
for approximately eight
Note: When the unit is reset, many user settings will be deleted, including paired
device information, selected ring tone and incoming call list. No phone numbers
will be deleted from the phone book when the unit is reset. Please refer to page 9
for instructions for resetting the phone book.
5
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
OPERATION
MenuꢀMode
The following settings may be adjusted using menu mode:
• Ring Tone
• Phone Book
• Hotline
Note: Menu mode may only be accessed when the unit is not connected to a phone.
To enter menu mode, press in and hold JOG for two seconds. "MENU MODE" will
appear on the display.
Press JOG to the right or left to scroll forward or backward through the three
menu options (RING TONE, PHONE BOOK and HOTLINE). When the desired option
appears in the display, press in on JOG to access that sub-menu.
After making changes within a sub-menu, press in and hold JOG for two seconds
to confirm. To return to the main menu from a sub-menu without saving changes,
press
one time. Press
again to exit menu mode.
RingꢀTone
1. While in menu mode, press JOG to the right or left until "RING TONE"
appears in the display.
2. Press in on JOG to enter the Ring Tone sub-menu.
3. Press JOG to the right or left to scroll through the following options:
RING TONE 1, RING TONE 2 or RING TONE 3. The unit will play a sample of each
ring tone as its name is displayed.
4. Select the desired ring tone option, and press in and hold JOG for two
seconds to confirm.
5. The name of the ring tone selected will appear in the display.
6. Press
to exit the menu.
6
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
OPERATION
MenuꢀModeꢀ(continued)
PhoneꢀBook
1. To manually input a phone book entry, enter menu mode, then press JOG to the
right or left until “PHONE BOOK” appears in the display.
2. Press in on JOG to enter the Phone Book sub-menu.
3. "INSERT NUM." will appear briefly on the display, then a flashing cursor will
prompt the entry of a phone number. Press JOG to the right or left to select the
desired number for the first digit. Press in on JOG to confirm the selection, and
move the cursor to the next digit. Repeat until the entire number has been
entered, then press in and hold JOG for two seconds. "SAVED NUMBER" will
appear in the display.
Note: Press
to backspace during number entry.
4. After the phone number is saved, a flashing cursor will prompt the entry of
a name. Press JOG to the right or left to select the desired first letter.
Press in on JOG to confirm the selection and move the cursor to the
next letter. Repeat until the entire name has been input, then press in and hold
JOG for two seconds. "SAVED NAME" will appear in the display.
Note: Press
to backspace during name entry. To enter a space, press JOG to
the left, then press it in briefly.
5. Press
to exit the menu.
Hotline
1. To program the Hotline speed dial button, enter menu mode, then press JOG to
the right or left until "HOTLINE" appears in the display.
2. Press in on JOG to enter the Hotline sub-menu.
7
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
OPERATION
MenuꢀModeꢀ(continued)
3. "INSERT NUM." will appear briefly on the display, then a flashing cursor will
prompt the entry of a phone number. Press JOG to the right or left to select the
desired number for the first digit. Press in on JOG to confirm the selection and
move the cursor to the next digit. Repeat until the entire number has been
entered, then press in and hold JOG for two seconds. "SAVED NUMBER" will
appear in the display.
Note: Press to backspace during number entry.
4. Press to exit the menu.
Note: The hotline number can be edited without entering menu mode by pressing H
(the hotline button) for three seconds. The hotline number will appear in the display
with the cursor flashing on the last digit. Press
the right or left to edit any number as desired.
to backspace, and press JOG to
UsingꢀtheꢀPhoneꢀBook
CallingꢀaꢀPhoneꢀBookꢀEntry
1. Press JOG to the left. "SELECT LETTER" will briefly appear in the display,
followed by "A".
2. Press JOG to the right or left to scroll through the alphabet and select
the first letter of the desired name. When the desired letter appears in the
display, press in on JOG. "SEARCHING" will appear in the display.
3. If the phone book contains an entry beginning with the selected letter, the name
and number will appear on the display. Press JOG to the right or left to scroll
through all phone book entries beginning with that letter.
4. When the desired name appears in the display, press
to connect the call.
EditingꢀaꢀPhoneꢀBookꢀEntry
Search for an entry as described in Calling a Phone Book Entry above. When the
desired entry is displayed, press in on JOG. The cursor will flash on the last digit.
Note: Press
as desired.
to backspace, and press JOG to the right or left to edit any number
8
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
OPERATION
UsingꢀtheꢀPhoneꢀBook
DeletingꢀaꢀPhoneꢀBookꢀEntry
Search for an entry as described in Calling a Phone Book Entry on page 8. When
the desired entry is displayed, press
for three seconds to delete.
DownloadingꢀPhoneꢀBookꢀContacts
Download individual contacts from any mobile phone that supports Object Push
Profile. Contacts will be downloaded one at a time.
1. Open the LCD flap while holding
. "OBJECT PUSH" will appear in the display.
2. Locate the desired number in the phone, and send it to the BTV30 using the
method outlined in the phone's instruction manual.
3. The display will show when the unit is "CONNECTED", "DOWNLOADING" and
"COMPLETED". After the download, the unit will return to object push mode.
4. Repeat steps 2 and 3 to add all desired phone book contacts.
5. Close the LCD flap to turn the power off, then reopen and begin pairing.
ResettingꢀtheꢀPhoneꢀBook
Note: The phone book may only be reset when the unit is not paired to a phone.
To reset the phone book, press and hold
for approximately 15 seconds.
"PHONEBOOK RESET" will appear in the display. The unit will begin resetting the
phone book. "RESETTING" will appear in the display.
Once the phone books is reset, the unit will perform a memory test, during which
time "TESTING" will appear in the display. After the test in complete, the unit will be
ready for use and "HELLO" will appear in the display. The reset process takes about
2 1/2 minutes to complete.
ChargingꢀtheꢀBattery
Remove the unit from the visor to charge. Plug the car charger into the charging
port on the unit, and connect the other end to the power supply.
9
®
®
BTV30ꢀBLUETOOTHꢀꢀSPEAKERPHONE
LIMITEDꢀONE-YEARꢀWARRANTY
This warranty gives you specific legal rights.
Whatꢀtoꢀdo?
You may also have other rights which vary
from state to state.
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a call.
Dual Electronics Corp. warrants this product
to the original purchaser to be free from
defects in material and workmanship for
a period of one year from the date of the
original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and
ship it by prepaid transportation with
a copy of the original receipt from the
retailer to an authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any
defect in material or workmanship or to
furnish an equal new, renewed or comparable
product (whichever is deemed necessary)
in exchange without charges, subject to
verification of the defect or malfunction and
proof of the date of purchase. Subsequent
replacement products are warranted for the
balance of the original warranty period.
3. Please describe your problem in writing
and include your name, a return UPS
shipping address (P.O. Box not acceptable),
and a daytime phone number with your
shipment.
4. For more information and for the location
of the nearest authorized service center
please contact us by one of the following
methods:
Whoꢀisꢀcovered?ꢀThis warranty is extended
to the original retail purchaser for products
purchased and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability,
Whatꢀisꢀcovered?ꢀThis warranty covers all
defects in material and workmanship in
this product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect,
product modification, improper installation,
incorrect line voltage, unauthorized repair or
failure to follow instructions supplied with the
product, or damage occurring during return
shipment of the product.
right, claim or remedy in contract or tort,
whether or not arising from the company’s
negligence, actual or imputed. No person or
representative is authorized to assume for the
company any other liability in connection with
the sale of this product. In no event shall the
company be liable for indirect, incidental or
consequential damages.
10
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2007 Dual Electronics Corp. All rights reserved.
MagnetꢀWarning
The BTV30 contains powerful magnets that may cause data loss
when exposed to certain devices or credit cards.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two con-
ditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interferences received, including interference that may cause undesired operations.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by
Movon is under license. Other trademarks and trade names are those of their respective owners.
NSA0407-V01
|