Owner’s Manual
Model Numbers:
DF3215
DF3215NH
Quality checked by:
Serial Number
Model Number
Part Number
Valued Customer,
Thank you and congratulations for purchasing a
Dimplex electric fireplace. Over the years, valuable
memories will occur around the warmth and comfort of
your hearth. Thank you for allowing our product to be
the backdrop for those special moments.
7207030100rev11
CONTENTS
Important Instructions . . . . . . . . . . . . . . . PAGE 4
Model and Serial Number Information. . . PAGE 6
Site Selection and Preparation . . . . . . . . PAGE 7
Fireplace Installation . . . . . . . . . . . . . . . . PAGE 7
Operation. . . . . . . . . . . . . . . . . . . . . . . . . PAGE 10
Maintenance . . . . . . . . . . . . . . . . . . . . . . PAGE 16
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . PAGE 20
3
IMPORTANT INSTRUCTIONS
Retain This User’s Guide For Future Reference
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electric shock, and injury to persons, including the
following:
1. Read all instructions before using the electric fireplace.
2. The heater is hot when in use. To avoid burns, do not let bare skin touch
hot surfaces. The trim around the heater outlet becomes hot during
heater operation. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front
of the unit (not applicable on DF3215NH model fireplaces).
3. Extreme caution is necessary when any heater is used by or near children
or invalids and whenever the unit is left operating and unattended (not
applicable on DF3215NH model fireplaces).
4. Always unplug the electric fireplace when not in use.
5. Do not operate any unit with a damaged cord or plug, or if the heater has
malfunctioned, or if the electric fireplace has been dropped or damaged in
any manner. Return heater to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. The electric fireplace is not intended for use in bathrooms, laundry areas
and similar indoor locations. Never locate heater where it may fall into a
bathtub or other water container.
8. Do not run the cord under carpeting. Do not cover cord with throw rugs,
runners, or the like. Arrange cord away from traffic area and where it will
not be tripped over.
9. To disconnect the unit, turn the controls off, then remove the plug from the
outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage to the
heater.
11. To prevent a possible fire, do not block air intake or exhaust in any manner.
Do not use on soft surfaces, like a bed, where openings may become
blocked (not applicable on DF3215NH model fireplaces).
12. All electrical heaters have hot and arcing or sparking parts inside. Do not
use in areas where gasoline, paint, or flammable liquids are used or stored
or where the unit will be exposed to flammable vapors (not applicable on
DF3215NH model fireplaces).
13. Do not modify the electric fireplace. Use it only as described in this
4
manual. Any other use not recommended by the manufacturer may cause
fire, electric shock or injury to persons.
14. Avoid the use of an extension cord. Extension cords may overheat and
cause a risk of fire. If you must use an extension cord, the cord must be
No. 14 AWG minimum size and rated no less than 1875 Watts.
15. Do not burn wood or other materials in the electric fireplace.
16. Do not strike the fireplace glass.
17. Always use a certified electrician should new circuits or outlets be required.
18. Always use properly grounded, fused and polarized outlets.
19. Disconnect all power supply before performing any cleaning, maintenance
or relocation of the unit.
20. When transporting or storing the unit and cord, keep in a dry place, free
from excessive vibration and store so as to avoid damage.
CAUTION
RISK OF ELEcTRIc ShOcK
DO NOT OPEN
NO USER-SERvIcEABLE PARTS INSIDE
SAVE THESE INSTRUCTIONS
! NOTE: Procedures and techniques that are considered important enough
to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will
result in damage to the equipment.
WARNING: Procedures and techniques which, if not carefully followed, will
expose the user to the risk of fire, serious injury, illness or death.
! NOTE: This equipment has been tested and found to comply with the
limits for class B digital device, pursuant to part 15 of the Fcc Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
·
·
·
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
connect the equipment into an outlet on a circuit different from that to
5
which the receiver is connected.
·
consult the dealer or an experienced radio/Tv technician for help.
Operation is subject to the following two conditions: (1) this device may not
cause interference and; (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Model And Serial Number Information
If you have any questions about our products please have the product
model and serial numbers available upon calling Dimplex customer
service. To locate the model and serial number see below (Figure 1).
Record the Part Number, Model Number and Serial Number on the
front cover of this manual for future reference.
Figure 1
Part Number
Serial Number
SERIAL No.
XXX
XX
6
! NOTE: A 15 Amp, 120 volt circuit is required. A dedicated circuit
is preferred but not essential in all cases. A dedicated circuit will
be required if, after installation, the circuit breaker trips or fuse
blows on a regular basis when the heater is operating. Additional
appliances on the same circuit may exceed the current rating of the
circuit breaker.
WARNING: Ensure the power cord is not installed so that it is
pinched or against a sharp edge and ensure that the power cord is
stored or secured to avoid tripping or snagging to reduce the risk of
fire, electric shock or injury to persons.
Construction and electrical outlet wiring must comply with local
building codes and other applicable regulations to reduce the risk
of fire, electric shock and injury to persons. Do not attempt to wire
your own new outlets or circuits. To reduce the risk of fire, electric
shock or injury to persons, always use a licensed electrician.
Site Selection And Preparation
This section provides instructions for selecting a location and preparing
the site to install the fireplace into your Dimplex mantel surround.
1. Select a suitable location that is not susceptible to moisture and is
away from drapes, furniture and high traffic.
2. For ease of electrical hook up you may wish to locate the fireplace
near an existing outlet (refer to NOTE 1).
3. Store the fireplace in a safe dry and dust free location.
! NOTE: The dimensions of the fireplace are 36 ½ inches (927 mm)
wide X 31 ¾ inches (806 mm) high X 13 inches (330 mm) deep.
The viewing area is 32 inches (813 mm) wide and 28 ¼ (715 mm)
high. The fireplace does not require any additional venting.
Fireplace Installation
1. Install the Bi-fold doors to the fireplace.
! IMPORTANT: Bi-fold doors MUST be installed to the firebox prior
to installing firebox to mantel.
7
Bi-fold Door Installation (Figure 2)
Figure 2
Bi-fold
Door
Mounting
hole
Door
Spacer
Bottom
Ledge
Screw
i. Remove the Bi-fold doors from packaging.
ii. Remove the Philips head screw and the door spacer from the
bottom edge of the Bi-fold door opposite of the door handle.
iii. Insert the door spacer into the bottom panel ledge mounting
hole.
iv. Insert the top edge of the Bi-fold door into the top door track on
the fireplace.
v. Secure the Bi-fold door to unit with supplied screw using a short
handled screwdriver.
! NOTE: If short handled screwdriver is not available tilt the unit
back.
vi. Repeat steps 2-5 for the other side.
2. Install the fireplace assembly into the mantel (refer to Dimplex
mantel assembly instructions).
8
! IMPORTANT: If not using a Dimplex mantel, the fireplace must
be installed in an enclosure with the following MINIMUM internal/
opening dimensions: 32 inches (813 mm) wide x 31 ¾ inches (806
mm) high x 13 ½ inches (343 mm) deep; and in such a way that the
plug and outlet can be accessed (Figure 3).
Figure 3
3. Removable mounting hardware must be used when installing this
unit into a new wall application, this unit must be able to be
removed from the opening to access the plug and outlet as well as
for servicing purposes. A custom trim may be used, permitting
easy and non-destructive removal.
4. Plug the unit into a 15 Amp/120 volt outlet. If the cord does not
reach, you may use an extension cord rated for a minimum of 1875
Watts.
WARNING: Ensure the power cord is not installed so that it is
pinched or against a sharp edge. Also ensure the power cord is
stored or secured to avoid tripping or snagging to reduce the risk of
fire, electric shock or injury to persons.
9
Operation
Electric Fireplace Manual Control
The manual controls for the fireplace are located in the upper right
hand corner (Figure 4).
Figure 4
Main
On/Off
Switch
Initialization
Button
SERIAL No.
XXX
XX
3 Position
Manual
Control
Indicator
Light
Main On/Off Switch
Supplies power to the 3 Position Manual control Switch.
3 Position Manual Control Switch
Remote (left position): The unit is operated with the remote control.
Flame (center position): The flame effect is turned on.
Flame & Heat (right position)*: The flame effect and heater are
turned on simultaneously. When the manual control is in the Flame
& Heat position the heater does not run on the remote operated
thermostat. When the heater is on the red indicator light is activated
on the firebox and the fan and heater are running on low.
! NOTE: When the manual control switch is in the Flame and Flame
& Heat positions, the fireplace unit will not operate with the remote
control.
10
* Flame only function of DF3215NH
Resetting The Temperature Cutoff Switch **
Should the heater overheat, an automatic switch will turn the heater
off and it will not come back on without being reset. The temperature
cutoff switch can be reset by unplugging the unit, waiting five (5)
minutes and plugging the unit back in.
CAUTION: If you need to continuously reset the heater, unplug the
unit and call Dimplex North America Limited at 1-888-346-7539 for
technical support.
** Not applicable on DF3215NH model fireplaces.
Remote Control
The remote control has a range of approximately 50 feet (15.25 m).
It does not have to be pointed at the fireplace and can pass through
most obstacles (including walls). It is supplied with 243 independent
frequencies to prevent interference with other units.
Battery Installation (Figure 5)
Figure 5
1. Depress the tab on the battery cover on the
back of the remote transmitter and remove
battery cover.
2. Install two (2) AAA batteries into the remote
control (included).
3. Ensure child lock is in the “unlocked”
position.
4. Replace the battery cover.
! NOTE: When the
symbol is present
on the remote control, it is recommended to
replace the batteries promptly to maintain
full functionality of the remote/fireplace.
Batteries
child Lock
The remote transmitter has a battery backup time of only several
hours.
11
Initializing the Remote Control
1. Plug cord into 120 volt wall outlet.
2. Ensure the Main On/Off Switch of the fireplace (Figure 4) is in the
On
position.
3. Set the 3 Position Manual control (Figure 4) to the Remote position
(left position).
4. Press and hold the Initialization Button on the unit (Figure 4).
5. While holding the Initialization Button, press the Flame/heat On/
Off button or the Purifire™ On/Off button on the remote control
transmitter (Figure 6).
6. Release the Initialization Button on the unit.
7. Press the Flame/heat On/Off button to turn the Flame/heat
function on or press the Purifire™ On/Off button to turn the
Purifire™ function on.
Figure 6
A
B
J
L
I
C
E
K
M
D
F
N
P
R
O
Q
H
G
12
Remote Control Functions (Figure 6)
A - Room Temperature
B - Set Temperature*
K - Dimmer Down/Firelight Off
L - Dimmer Up/Firelight On
M - Flame Speed Down
N - Flame Speed Up
C - Dimmer/Firelight Control
D - Flame Speed Control
E - Slow Start/Fading Embers
Control
O - Slow Start/Fading Embers
Off
F - Purifire™ Speed
G - Flame & Heat On/Off
H - Purifire™ On/Off
I - Temperature Down*
J - Temperature Up*
P - Slow Start/Fading Embers
On/Timer Cycle
Q - Purifire™ Low Speed
R - Purifire™ High Speed
*
The set temperature buttons are not operational on the DF3215Nh model
fireplaces.
B - Set Temperature*
1. Press G - Flame & Heat On/Off button to turn the fireplace on.
2. Press J - Temperature Up to raise thermostat.
3. Press I - Temperature Down to lower the thermostat.
4. Press both J - Temperature Up and I - Temperature Down to
change °F to °c.
* Not applicable on DF3215NH model fireplaces.
C - Dimmer/Firelight Control
1. Press the G - Flame & Heat On/Off button to turn the Flame &
heat on.
2. Repeatedly press the L - Dimmer Up/Firelight On or K - Dimmer
Down/Firelight Off button to increase or decrease the brightness
of the upper lights.
3. To activate the Firelight, continue pressing L - Dimmer Up/Fire-
light On until the Firelight On icon is shown on the display screen.
4. To shut the Firelight off continue pressing the K - Dimmer Down/
Firelight Off button until the Firelight Off is shown on the display.
13
D - Flame Speed Control
1. Press the G - Flame & Heat On/Off button to turn the Flame &
heat on.
2. Press the N - Flame Speed Up button to increase the speed of the
flame.
3. Press the M - Flame Speed Down button to decrease the speed of
the flame.
E - Slow Start/Fading Embers Control
The Slow Start function simulates a starting fire. The function is
automatically programmed for 30 seconds and the timer setting cannot
be changed. The Fading Embers function simulates a fire going out.
The Fading Embers timer can be set to 1, 5 or 10 minutes.
1. Press the P - Slow Start/Fading Embers On/Timer Cycle button
to turn the Slow Start/Fading Embers function on.
2. Press the P - Slow Start/Fading Embers On/Timer Cycle button
repeatedly to set the Fading Embers timer to 1, 5 or 10 minutes.
3. Press the O - Slow Start/Fading Embers Off button to turn the
Fading Embers timer function off.
F - Purifire™ Speed
When the Purifire™ function is on, the Purifire™ symbol will flash.
When off the symbol will be solid. The default setting for the Purifire™
is set at low speed.
1. Press the H - Purifire™ On/Off button to turn the Purifire™
function On.
2. Press the Q - Purifire™ Low Speed to decrease the Purifire™
speed or the R - Purifire™ High Speed to increase the speed.
3. Press the H - Purifire™ On/Off button to turn the Purifire™
function off.
! NOTE: To turn the Flame & heat and Purifire™ off, press both
control buttons simultaneously.
G - Flame & Heat On/Off *
Press the G - Flame & Heat On/Off button to turn the Flame & heat
function on. When the B - Set Temperature is higher then the
14
A - Room Temperature the heat will come on. To turn the heat off,
lower the B - Set Temperature so that it’s setting is lower then the A -
Room Temperature. The default temperature setting is 72°F (22°c).
! NOTE: When using the remote control the heater runs on a
thermostat. Press the J - Temperature Up or I - Temperature
Down button to adjust the B - Set Temperature. Once the desired
set temperature is reached the heater will turn off. The heater will
cycle on and off to maintain the desired set temperature.
* Not applicable on DF3215Nh model fireplaces.
Child Lock
1. Depress tab on the battery cover on the back of the remote
transmitter and remove the battery cover (Figure 7).
Figure 7
Unlocked
Locked
child Lock Switch
child Lock
2. Move Child Lock tab to the right to lock the remote transmitter.
3. Move Child Lock tab back to the left to unlock the remote
transmitter.
4. Replace the battery cover.
15
! NOTE: To temporarily unlock the remote transmitter press (in
order) I - Temperature Down then J - Temperature Up then K -
Dimmer Down/Firelight Off.
When the remote transmitter’s backlight is illuminated the Child Lock
is bypassed. When the backlight is off the Child Lock is re-activated.
Frequency Interference
If the fireplace does not respond properly to the remote control, the
remote operating frequency may have to be reset. The remote control
can send another frequency code to the circuit board to eliminate
interference.
1. Simultaneously press the O - Slow Start/Fading Embers Off
button and the Q - Purifire™ Low Speed button on the remote
control.
2. “CODE” will appear.
3. Release the Slow Start/Fading Embers Off button and the
Purifire™ Low Speed button.
4. Press and hold the Initialization Button on the unit (Figure 4).
5. Press the G - Flame & Heat On/Off button on the remote and
release the Initialization Button.
Your remote will now have a different frequency communicating with
the fireplace.
Maintenance
WARNING: Disconnect power before attempting any maintenance
or cleaning to reduce the risk of fire, electric shock or damage to
persons.
Light Bulb Replacement
Allow at least five (5) minutes for light bulbs to cool before touching
bulbs to avoid accidental burning of skin.
Light bulbs need to be replaced when you notice a dark section of
the flame or when the clarity and detail of the log ember bed exterior
disappears. There are four (4) bulbs under the log set, which generate
the flames and embers, and two (2) bulbs above the log that illuminate
the log exterior.
16
Lower Light Bulb Requirements
Quantity of four (4) clear chandelier or candelabra bulbs with an E-12
(small) socket base, 60 Watt rating. Example: GE 60Bc or Philips 60
cTc.
Do not exceed 60 Watts per bulb.
Helpful Hints
It is a good idea to replace all light bulbs at one time if they are close to
the end of their rated life. Group replacement will reduce the number
of times you need to open the unit to replace light bulbs. care must be
taken when removing the Log Set as the Log Set contains LED’s and
wires.
To access the lower light bulb area (Figure 8):
1. Open the Bi-fold doors.
2. Pull the front edge of the plastic Ember Bed or plastic grate up and
forward until the rear tab releases from the ledge located at the
bottom of the mirror.
! IMPORTANT: Only handle the Log Set by the Ember Bed.
! NOTE: Log Set fits
tightly into firebox, some
force may be necessary
to remove.
Figure 8
Light Bulbs
LED Wire
harness
3. Set Log Set in front of
firebox.
4. Disconnect the Log Set
LED wire harness from
unit.
5. Lift the left side of the
flame rod out of the
mounting bracket.
Ember
Bed
6. Examine the bulbs to determine which bulbs require
replacement.
7. Unscrew bulbs counter clockwise.
17
8. Insert new bulbs.
9. Install the left side of the flame rod to the mounting bracket.
10.Reconnect the Log Set LED Wire harness.
11.Replace the Log Set by
inserting the rear tab of the
Ember Bed under the mirror
and push down on the front
edge of the Ember Bed until it
snaps into place (Figure 9).
Figure 9
Back
Ledge
Log
Ember
Bed
! NOTE: Ensure the Log Set is
installed tightly under the back
ledge to prevent light leakage.
Front
Edge
Rear
Tab
Side Section
12.close the Bi-fold doors.
Upper Light Bulb Requirements
Quantity of two (2) clear chandelier
or candelabra bulbs with an E-12
(small) socket base, 25 Watt rating.
Figure 10
Upper Light
Do not exceed 25 Watts per bulb.
To access the upper light bulb
area:
Screw
1. Open the Bi-fold doors.
2. Remove upper light bracket with
a screwdriver (Figure 10).
3. Replace bulb.
4. Reassemble in the reverse order
as above.
Upper Light Bracket
Purifire™ Filter (Figure 11)
The Purifire™ filter supplied in your fireplace is reusable and washable.
The filter should be cleaned or replaced on average once a year.
To clean the filter gently tap filter on a hard surface to dislodge any
loose dirt or debris, and then clean with water. No soap or cleaning
products are recommended. The filter size is 20 inches x 10 inches
18
x 1 inch rated at MERv 10. If using an after market filter follow the
manufacturers recommended replacement instructions.
To replace filter:
1. Open the Bi-fold
Figure 11
doors.
Air Filter
2. Remove the three
Bracket
(3) mounting screws
from the Air Filter
Bracket.
3. Remove the Air
Filter Bracket
assembly from the
firebox.
Mounting
Screws
4. Slide Filter out of Air
Filter Bracket.
5. Replace filter and
reassemble in
reverse order as above.
! NOTE: If after market air filter is used ensure it is installed
according to the manufacturer’s recommended instructions.
Glass Cleaning
The glass is cleaned in the factory during the assembly operation.
During shipment, installation, handling, etc., the glass may collect dust
particles, these can be removed by dusting lightly with a clean dry
cloth.
To remove fingerprints or other marks, the glass can be cleaned with
a damp cloth. To prevent scratching, do not use abrasive cleaners or
spray liquids on the glass surface.
Fireplace Surface Cleaning
Use a cloth dampened with warm water only to clean painted surfaces
of the electric fireplace. Do not use abrasive cleaners.
19
Ten Year Limited Warranty
Products to which this limited warranty applies
This limited warranty applies to the following model of your newly purchased Dimplex
electric fireplace DF3215, DF3215NH and to newly purchased Dimplex fireplace
surrounds (mantels) and trims. This limited warranty applies only to purchases made in
any province of canada except for Yukon Territory, Nunavut, or Northwest Territories or
in any of the 50 States of the USA (and the District of columbia) except for hawaii and
Alaska. This limited warranty applies to the original purchaser of the product only and
is not transferable.
Products excluded from this limited warranty
Light bulbs and Purifire™ filters are not covered by this limited warranty and are the
sole responsibility of the owner/purchaser. Products purchased in Yukon Territory,
Nunavut, Northwest Territories, hawaii, or Alaska are not covered by this limited
warranty. Products purchased in these States, provinces, or territories are sold AS
IS without warranty or condition of any kind (including, without limitation, any implied
warranties or conditions of merchantability or fitness for a particular purpose) and the
entire risk of as to the quality and performance of the products is with the purchaser,
and in the event of a defect the purchaser assumes the entire cost of all necessary
servicing or repair.
What this limited warranty covers and for how long
Products, other than fireplace surrounds (mantels) and trims, covered by this limited
warranty have been tested and inspected prior to shipment. Subject to the provisions
of this warranty, Dimplex warrants such products to be free from defects in material and
workmanship for a period of 10 years from the date of the first purchase of such products
as follows: (a) a repair or replacement warranty on defective products or parts, including
in-home services, for the first year following the date of first purchase; and (b) thereafter,
a replacement of parts warranty on defective products and parts (with no in-home
services) for the 9 year period commencing on the first anniversary of first purchase and
ending on the tenth anniversary of the date of first purchase.
Dimplex fireplace surrounds (mantels) and trims covered by this limited warranty
have been tested and inspected prior to shipment and, subject to the provisions of
this warranty, Dimplex warrants such products to be free from defects in material and
workmanship for a period of 1 year from the date of first purchase of such products.
Warranty services do not include in-home services.
The above section is a summary only of your warranty rights. Please review the
remaining provisions of this warranty for your specific rights.
The limited 10 year warranty period for products other than fireplace surrounds (mantels)
and trims and the limited 1 year warranty period for fireplace surrounds (mantels) and
trims also applies to any implied warranties that may exist under applicable law. Some
jurisdictions do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to the purchaser.
What this limited warranty does not cover
This limited warranty does not apply to products that have been repaired (except by
20
Dimplex or its authorized service representatives) or otherwise altered. This limited
warranty does further not apply to defects resulting from misuse, abuse, accident,
neglect, incorrect installation, improper maintenance or handling, or operation with an
incorrect power source.
What you must do to get service under this limited warranty
Defects must be brought to the attention of Dimplex Technical Service by contacting
Dimplex at 1-888-DIMPLEX (1-888-346-7539), or 1367 Industrial Road, cambridge
Ontario, canada N1R 7G8. Please have proof of purchase, catalogue/model and serial
numbers available when calling. Limited warranty service requires a proof of purchase
of the product.
What Dimplex will do in the event of a defect
In the event a product or part covered by this limited warranty is proven to be defective in
material or workmanship during (i) the 10 year limited warranty period for products other
than fireplace surrounds (mantels) and trims, and (ii) the 1 year limited warranty period
for surrounds (mantels) and trims, you have the following rights:
•
Limited warranty service will be performed solely by dealers or service agents of
Dimplex authorized to provide limited warranty services.
•
For products (other than surrounds (mantels) and trims) for the period ending
at midnight on the first anniversary of the date of first purchase, Dimplex will
in its sole discretion either repair or replace such defective product or part without
charge. If Dimplex is unable to repair or replace such product or part, or if repair
or replacement is not commercially practicable or cannot be timely made, Dimplex
may, in lieu of repair or replacement, choose to refund the purchase price for such
product or part. This limited warranty entitles the purchaser to on-site or in-home
warranty services. Accordingly, Dimplex will be responsible for all labour and
transportation costs associated with the repair or replacement of the product or part
except as follows: (i) charges may be levied for travel costs incurred to travel to
the purchaser’s site where the product is located if the purchaser’s site is beyond
30 miles (48 km) from the closest service depot of Dimplex’s dealer or service
agent; and (ii) the purchaser is solely responsible for providing clear access to all
serviceable parts of the product.
•
For products (other than surrounds (mantels) and trims) for the period
commencing at 12:01 a.m. on the day after the first anniversary of the first
purchase and ending at midnight on the tenth anniversary of the date of
first purchase, this limited warranty entitles the purchaser to replacement parts
only without charge. If Dimplex is unable to replace such part, or if replacement
is not commercially practicable or cannot be timely made, Dimplex may, in lieu of
replacement, choose to refund the purchase price for such part. The purchaser
shall not be entitled to on-site or in-home warranty services. The purchaser shall
be responsible for all expenses incurred for the removal of the part and installation
of the replacement part including, without limitation, all shipping costs and
transportation costs to and from the authorized dealer’s or service agent’s place of
business and all labour costs. Such costs shall not be the responsibility of Dimplex.
•
For surrounds (mantels) and trims for the period ending at midnight on the
first anniversary of the date of first purchase, Dimplex will in its sole discretion
21
either repair or replace such defective surrounds (mantels) and trims or part thereof
without charge. If Dimplex is unable to repair or replace such product or part, or
if repair or replacement is not commercially practicable or cannot be timely made,
Dimplex may, in lieu of repair or replacement, choose to refund the purchase price
for such product or part. The purchaser shall not be entitled to on-site or in-house
services. The purchaser is responsible for all expenses incurred for repair or
replacement of such product or part including, without limitation, all shipping costs
and transportation costs to and from the authorized dealer’s or service agent’s
business and all labour costs. Such costs shall not be the responsibility of Dimplex.
•
On-site or in-home services not provided under this warranty may be performed at
the purchaser’s specific request and expense at Dimplex’s then-current rates for
such services.
What Dimplex and its dealers and service agents are also not responsible for:
IN NO EvENT WILL DIMPLEX, OR ITS DIREcTORS, OFFIcERS, OR AGENTS, BE
LIABLE TO ThE PURchASER OR ANY ThIRD PARTY, WhEThER IN cONTRAcT,
IN TORT, OR ON ANY OThER BASIS, FOR ANY INDIREcT, SPEcIAL, PUNITIvE,
EXEMPLARY, cONSEQUENTIAL, OR INcIDENTAL LOSS, cOST, OR DAMAGE
ARISING OUT OF OR IN cONNEcTION WITh ThE SALE, MAINTENANcE, USE,
OR INABILITY TO USE ThE PRODUcT, EvEN IF DIMPLEX OR ITS DIREcTORS,
OFFIcERS, OR AGENTS hAvE BEEN ADvISED OF ThE POSSIBILITY OF SUch
LOSSES, cOSTS OR DAMAGES, OR IF SUch LOSSES, cOSTS, OR DAMAGES
ARE FORESEEABLE. IN NO EvENT WILL DIMPLEX, OR ITS OFFIcERS,
DIREcTORS, OR AGENTS BE LIABLE FOR ANY DIREcT LOSSES, cOSTS, OR
DAMAGES ThAT EXcEED ThE PURchASE PRIcE OF ThE PRODUcT.
SOME JURISDIcTIONS DO NOT ALLOW ThE EXcLUSION OR LIMITATION OF
INcIDENTAL OR cONSEQUENTIAL DAMAGES, SO ThE ABOvE LIMITATION OR
EXcLUSION MAY NOT APPLY TO ThE PURchASER.
How State and Provincial law apply
This limited warranty gives you specific legal rights, and you may also have other
rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations
convention on contracts for the Sale of Goods shall not apply to this limited warranty
or the sale of products covered by this limited warranty.
Dimplex North America Limited
1367 Industrial Road cambridge ON
canada N1R 7G8
© 2010 Dimplex North America Limited
22
|