Cooper Lighting Indoor Furnishings Vision Wall User Manual

TM  
TM  
VISION WALL  
Sheet 4 of 4  
VISION WALL  
Sheet 1 of 4  
INSTALLATION INSTRUCTIONS  
General: Upon receipt of fixture thoroughly inspect for any  
freight damage, which should be brought to the attention of  
the delivery carrier. Compare the catalog description listed  
on the packing slip with the fixture label on the housing to  
assure you have received the correct merchandise.  
INSTALLATION INSTRUCTIONS  
12/29/03  
IMI-498  
12/29/03  
IMI-498  
IMPORTANT: Read carefully before installing fixture. Retain for future reference.  
IMPORTANT: Read carefully before installing fixture. Retain for future reference.  
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.  
Safety: This fixture must be wired in accordance with  
the national electrical code and applicable local codes  
and ordinance. Proper grounding is required to insure  
personal safety. Carefully observe grounding procedure  
under installation section. All work should be done by a  
qualified electrician.  
Adjustment Of Light Throw  
Your Vision Wall luminaire has an adjustable forward light  
throw.  
Adjustment  
Screw  
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.  
1. Obtain a 3/16" allen wrench.  
2. Locate the stainless steel button head screw on the  
Your Vision Wall Luminaire has three different types of  
mounting interface:  
outside of the fixture (See Fig. 4).  
3. Turn the screw clockwise to pivot the reflector and throw  
1. Standard Mount—mounts to any standard 4" J-box.  
the light forward.  
(Included with every fixture) (See Fig. 1).  
Fig. 4  
4. You may monitor the reflector rotation by viewing the  
bottom edge of the reflector and the indicator located  
inside the fixture. This is viewable through the glass  
(See Fig. 5).  
2. Embedded Mount—mounts to a plate embedded into  
the wall (Optional Accessory VWM/EM) (See Fig. 2).  
3. Thru Way Box—mounts to surface mounted casting,  
allowing a conduit run (Optional Accessory VWM/TB)  
(See Fig. 3).  
5. Rotating the screw counter-clockwise brings the reflector  
back down to zero.  
Embedded Mount Kit  
NOTE:  
Fig. 2  
EMBEDDED MOUNT  
VWM/EM  
Please refer to your mounting kit for specific instructions.  
Thru Way Mounting  
Degree Indicator  
Fig. 5  
CAUTION:  
Prior to installing lamp in the fixture, verify that lamp source and wattage correspond with the fixture label. Lamp should  
be screwed securely into the socket. Do not over tighten.  
WARNING:  
Recheck to be sure that the fixture has been wired properly. Improper wiring may result in ballast failure which voids all  
Conduit run by others  
warranties.  
Standard Mount Kit  
4" J Box (By Others)  
screws to J Box  
Cleaning  
The reflector and door glass may be cleaned with any suitable non-abrasive glass cleaning solution, soap, or detergent  
and rinse with clean water. The reflectors efficiency will be retained only if cleaned at regular intervals. Clean with mild  
soap or detergent and water, or liquid wax emulsion. The refractor should also be cleaned along with the reflector, using  
care not to chip glass surfaces.  
Fig. 1  
STANDARD MOUNT  
Fig. 3  
THRU-WAY BOX  
VWM/TB  
CAUTION:  
Do not use abrasive, strong alkaline or acid cleaners.  
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible  
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for users purpose, please  
contact your nearest representative.  
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible  
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for users purpose, please  
contact your nearest representative.  
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 AVU033142  
AVU033142  
 

Compaq Power Supply R6000 Series User Manual
Cooper Lighting Indoor Furnishings WTS Series User Manual
Cradlepoint Network Router CBR450 User Manual
Curtis CRT Television TV2710B User Manual
Cypress Computer Hardware CY7C68000A User Manual
Delta Electronics Power Supply SIWC1360 User Manual
Edelbrock Camera Accessories 65732 User Manual
Edimax Technology Network Card EW 7317LDg User Manual
Electro Voice Stereo Amplifier CPS28 User Manual
FujiFilm Digital Camera 16010710 User Manual