DESCRIPTION
Catalog #
Project
Type
Date
An adjustable Single-lamp Recessed fixture for trimless installation suitable for
downlighting and accent applications. Utilizes ONE (1) 12V MR11 lamp.
For remodel applications. Insulation must be kept 3” from all sides and at least
1” above the housing.
Comments
Prepared by
SPECIFICATION FEATURES
A... Housing
D... Electrical
secured with threadless, bayonet action.
Housing and junction box are aluminum,
trimless meshplate is steel with powder
coated finish. Perforated meshplate
allows for trimless installation in drywall/
plaster ceilings by allowing the ceiling’s
mudding compound to be applied right
up to the edge of the fixture opening.
Includes a beveled “knife-edge” lips to
ensure a clean edge. Can accommodate
various ceiling thickness.
Integral electronic or magnetic low voltage Optional retractable arm is available for
COMBOLIGHT®
Next Generation
Recessed
transformers. Transformers and electrical
are mounted in a separate metal enclosure
lamp pulldown and extreme aiming.
box attached to the junction box with 18” F ... Mounting
of flexible conduit. Transformer enclosure
Mounting clips are provided which
includes a separated wiring compartment mount the housing edge flush with the
and two knockouts for conduit entry.
finished ceiling line. Mounting clips are
Single-Lamp Fixture
Transformer enclosure features perforated secured to the housing through the
metal door for easy maintenance access
and cooler operation. Entire electrical
meshplate with screws.
One (1) Light
12V MR11
assembly (jbox and transformer enclosure) G... Labels
B... System Protection:
is removable from the housing for easy
maintenance.
cULus listed for non-type IC
applications, suitable for use in damp
locations.
Thermal protection provided to guard
against overheating and misuse of
insulation over and around fixture. Vent
E ... Lamps
holes in housing provide cooler operation. One (1) 12V MR11 lamp mounted in
adjustable double gimbal. Lamp holder is
Ceiling Cut-Out: 5.00” x 5.00
Remodel Housing
Trimless
C... Junction Box
removable and may be regressed 1” for
Junction Box is UL listed for through branch additional cut-off. Lamp can accept up to
wiring, 6 #12 90º C supply conductors or
60º C for end of run. The fixture is also UL
three optical accessories (i.e. lens + hex
louver + snoot). 45º x 45º locking lamp
listed as ‘access above ceiling not required’. adjustment. Beveled-edge lamp ring is
Double
Gimbal
8.50”
4.70”
45º x 45º
Adjust
6.25”
1.60”
5.75”
Required
above
10.24”
10.24”
3.88”
ceiling
3.39”
Integral Low Voltage
Transformers
6.50”
3.88”
Separate Wiring
Compartment
Perforated
Meshplate
18” flexible conduit
NOTES:
Thermal
Protector
De-Rated wattage labels are available.
12V Primary voltage is available.
ORDERING INFORMATION
C1
R
N
N
Configuration
Lamp Type / Wattage Label
Power Supply
Lamp Mechanism
Trim Insert Finish
C1 = COMBOLIGHT
Recessed One (1) Light
020M11 = 20 Watt max. MR11 12V
035M11 = 35 Watt max. MR11 12V
Voltage
G = Double Gimbal
N = Trimless
= 120V
= 277V
R
= Retractable Double Gimbal
1
2
Housing
Power Supply
Trim Insert
N = Trimless
Housing Interior/Electrical Door/Sleeve
R = Remodel
E = Electronic Low Voltage
Transformer
Finish
W = White
M = Magnetic Low Voltage
Transformer
B
S
= Black
= Industrial Silver
rev 121107
Specifications and Dimensions subject to change without notice.
RSA Lighting • 7945 Orion Ave. • Van Nuys, CA 91406 • 818-349-3030 • FAX 818-349-3031
|