Synergy.doc
Synergy® V
Universal / DVR Remote Control
Model RT-U62CD
Programming And Operating Instructions
Rev. 09/04
© 2004 CONTEC CORPORATION
- 1 -
Synergy.doc
2. From the Cable Setup Code list, locate the 3-digit code for your brand / model and enter it on the keypad
of the remote control. The set-top terminal will turn off.
3. Then, press [OK] to lock in the code. The power / mode buttons will blink 3-times and go out.
Cable Setup Codes
Motorola
DCT (all except DVR)
CFT 2200
DCT – 62xx series DVR terminals
001
001
002
Jerrold
DL4, DP(V), DQN(V), DPBB
003
Scientific Atlanta
Explorer® 8000 (SARA - RT-U59C)
412
Explorer® 8000 (Passport - RT-U61CP) 413
Explorer®
8600X
8600
004
005
006
Pace
510 Digital
HD Digital
004
010
Pioneer
Voyager
BA-V1000, BA-V2000
®
004
007
Tocom
5503VIP, 5507, 5508
008
Zenith
MM 2500
Digital
009
013
5. Programming Your TV, VCR, DVD, and AUDIO Devices
Code-Entry Programming
1. Turn on all the electronic devices (TV, VCR, DVD, AUDIO) you want to program the remote to operate.
2. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL Æ
TV Æ VCR Æ DVD Æ AUDIO Æ CBL…).
3. a. To program your TV, locate the 3-digit code for your brand in the TV Setup Code list and enter it on the
keypad of the remote control. Entry of the correct code will cause your TV to turn off. If multiple codes
are listed for your brand, you may have to try several different codes until your TV turns off.
b. As soon as you have entered a 3-digit code that turns your TV off, press [MUTE].
1. If the TV turns back on, press [OK] to lock in the code. The power / mode buttons will blink 3-
times and go out.
Or
2. If the TV does not turn back on, enter a different 3-digit setup code until your TV turns back on.
Then press [OK] to lock in the code. The power / mode buttons will blink 3-times and go out.
4. To program your VCR, refer to the VCR / DVD Setup Code lists and repeat steps 2 and 3 above.
5. To program your DVD, refer to the VCR / DVD Setup Code lists and repeat steps 2 and 3 above.
6. To program your AUDIO equipment, refer to the AUDIO Setup Code list and repeat steps 2 and 3 above.
- 3 -
Synergy.doc
Point and Press® Programming
This method allows you to program the remote control without using codes. Instead, the remote control
automatically finds the correct command that you select in a variety of codes until you find the code that operates
your device. You then lock in the correct code as described below.
The following instructions describe how to program your remote control using the [CH +] or [CH -] buttons ("Power"
function during programming). You may also program your remote control using other buttons / functions as
described in Section 14. When using this method, there are several important points to remember:
•
•
The order in which you program your electronic devices is not important.
There may be several codes that turn your electronic devices on / off (or perform other functions). Once you
lock-in a code, be sure to check the available functions for that device (i.e. TV - Vol +/-, Mute, TV Input
(Video Source button); VCR - Play, Stop..; DVD - Play, Stop...; AUDIO - Vol +/-, Mute) to see if they are
operating.
•
•
While the remote is searching for the correct setup code(s) for your electronic devices, it is possible that
other (previously programmed) devices may turn on / off (or perform other functions). If this occurs,
continue pressing the [CH +] or [CH -] buttons (or the buttons described in Section 14) until you find the
correct code for the device you are programming.
It may take several minutes for the remote to find the correct code that turns your device off (or performs
another selected function). During this time, the power / mode buttons will illuminate in fast-rotation (i.e.
CBL Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL…).
Programming your electronic devices using the [Ch +] or [Ch -] buttons (“Power” function during
programming)...
1. Turn on all the electronic devices (TV, VCR, DVD, AUDIO) you want to program the remote to operate.
2. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL Æ
TV Æ VCR Æ DVD Æ AUDIO Æ CBL…).
3. Press and hold the [CH +] button until one device turns off. While you are pressing the [CH +] button, the
power / mode buttons will illuminate in fast-rotation. As soon as one device turns off, release the [CH +]
button.
4. Press [MUTE]. If the device that turned off...
a. Turns back on, press [OK] to lock in this code. The power / mode buttons will blink 3-times and go
out.
Or
b. Does not turn back on, press [CH -] one step at a time until that device turns back on. Each time you
press the [CH -] button, the power / mode buttons will illuminate once in reverse fast-rotation (AUDIO
Æ DVD Æ VCR Æ TV Æ CBL).
Once you have found a code that turns the device on / off, press [OK] to lock in this code. The
power / mode buttons will blink 3-times and go out.
5. Repeat steps 2 to 4 above for each of the remaining electronic devices you wish to program the remote to
operate.
6. Programming Your TV / VCR Combination
1. First, turn on your TV / VCR combination device and install a VHS tape.
- 4 -
Synergy.doc
2. Next, program your remote to operate the TV functions.
Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates the
TV functions (Power, Vol +/-, Mute) of your TV / VCR combination.
3. Last, program your remote to operate the VCR functions.
Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit VCR
Setup Code for your brand until a code is found that operates the transport functions (Play, Stop, Rew,
Pause, Rec) functions of your TV / VCR combination.
7. Programming Your TV / DVD or TV / VCR / DVD Combination
1. First, turn on your TV / DVD combination device and install a DVD.
2. Next, program your remote to operate the TV functions.
Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates the
TV functions (Power, Vol S/T, Mute, Ch S/T, 0-9) of your TV / DVD unit.
3. Last, program your remote to operate the DVD functions.
Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit DVD
Setup Code for your brand until a code is found that operates the transport functions (PLAY, STOP, REW,
FWD, PAUSE, REC) of your TV / DVD unit.
Before you can test for the correct DVD setup code, you must first press the [MODE] button, then [DVD]
button to put the remote in its DVD mode.
4. If you have a TV / VCR / DVD combination unit, you would then program your remote to operate the VCR
functions.
Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit VCR
Setup Code for your brand until a code is found that operates the VCR transport functions (PLAY, STOP,
REW, FWD, PAUSE, REC) of your TV / DVD / VCR unit.
Before you can test for the correct VCR setup code, you must first press the [MODE] button, then [VCR]
button first to put the remote in its VCR mode.
TV Setup Codes
Admiral
Adventura
026 054 211
047
Advent
Aiwa
072 094 425
214
Akai
053
Amark
Amstrad
Anam
023 215
157
217 218 219 220 221
222 223
053
AOC
Apex
Audiovox
Belcor
030 038 427
220
073
Bell & Howell
Broksonic
Brokwood
Candle
Centurion
Citizen
211
165 167
073
068 091
095 107 108
068 091 211 233
073 095
147
Concerto
Contec
- 5 -
Synergy.doc
Coronado
Craig
023
223
Crown
023
Curtis Mathes
016 054 107 108 211
213
Daewoo
051 068 073 095 158
159 189 191 194 196
197 198 200 202 204
205 206 207 209
073 095 107 108
073
Daytron
Dumont
Electro Home
Elektra
073 095
353
Emerson
016 023 053 064 103
139 158 159 164 165
166 167 168 169 392
400 401 402 408 415
073 095
Envision
Fisher
Funai
355 356
047
GE
Gateway
015 018 042 044 049
426
054 055 068 073 090
095 101 102 103 389
390 396 403 406 407
023 048 053 068 073
090 095 107 108 233
360
Gibralta
Goldstar (LG)
023 053 068 073 090
107 108 233 360 361
233
Grundig
Hall Mark
073 095
Hitachi
023 068 095 096 097
098 099 100
Inkel
364
JC Penney
039 053 068 073 092
095 102 355
JVC
104 105 106 396 397
410
Kawasho
KMC
073 095
023
KTV
Kurazai
LG (Goldstar)
023 053 233 366
211 213
023 053 068 073 090
107 108 233 360 361
211 213
Lodgenet
Logik
211 213
Luxman
068 073 095
LXI
024 026 157
Magnavox (Philips)
023 068 071 073 089
090 091 093 134 385
387 397 404 072
211 213
053 107 108 109
215
Majestic
Marantz
Megatron
Memorex
090 211 213 355 388
405
MGA / Mitsubishi
Montgomery Ward
053 068 073 090 095
107 109 110 216 384
394 395 398 399 417
022 023 026 053 071
072 108 211 213
028 068 090 108 200
019 159 160 161 162
163 382
NEC
Orion
Panasonic
042 043 044 045 046
429
Philco
023 053 068 071 072
091
Philips(Magnavox)
023 068 071 073 089
090 091 093 134 385
387 397 404 072
- 6 -
Synergy.doc
Pilot
073 094 233
Pioneer
Portland
ProScan
Proton
111 144 383
023 068
055 070
090 371 372
Pulsar
073
Quasar
Radio Shack
Realistic
RCA
044
073
022 166 168
042 052 053 054 055
069 070 416
Sampo
090 108
Samsung
015 016 017 023 031
090 107 108 134 147
151 153 386 411
Sansui
Sanyo
Scott
423 424
353 355 356 376 377
090 108 168
Sears
023 031 038 039 068
353 355 356
Sharp
016 022 023 024 025
026 027 028 029 393
395 409
Signature 2000
Sony
023 026 108 211 213
014 020 021
Soundesign
Squareview
Supre-Macy
Sylvania
091
157
380
068 071 072 090 091
093 107 108 157 158
419
Symphonic
Tatung
047 157 419
044
Techwood
Teknika
068
023 068 072 091 168
213
Telerent
Tera
023 213
381
Tevion
065 414
TMK
068 090
Toshiba
Totevision
Universal
Vidtech
030 031 038 039
233
068 102
068
Viewsonic
Wards
428
068 090
White Westinghouse
XR-1000
Yamaha
York
211 408
213
068
090 108
Zenith
047 048 049 050 051
391 405 406 434
VCR Setup Codes
Admiral
Adventura
Aiwa
066 075
132
Akai
269 275 336 351 352
354
Audio Dynamics
Bell & Howell
Broksonic
Canon
243 291
357
333 337 358 359
086 362
Citizen
Colortyme
Craig
033 172 247 331
291
172 363
Curtis Mathes
Daewoo
086 112 247 291
033 343 344 345 346
347
Daytron
DBX
345 365
243 291
Dynatech
132
- 7 -
Synergy.doc
Emerson
033 086 132 326 327
331 332 333 334 335
336 337 338 339 340
341 342
Fisher
035 081 357 363
Funai
132
GE
086 172 174
Go Video
Goldstar (LG)
Harman Kardon
Hitachi
348 349 350
247 331
291
078 132
Instant Replay
JC Penney
JCL
086
078 086 172 238 291
086
JVC
120 128 243 247 250
253
Kenwood
LG (Goldstar)
Lloyd
120 132 238 243 247
247 331
132
Logik
367
LXI
132 331
Magnavox (Philips)
Marantz
086 132 183 172
086 172 183 238 247
291
Marta
331
Matsui
Memorex
368
132 238 331 363 369
370
Mitsubishi
MTC
255 258
132 172
Montgomery Ward
Multi Tech
NEC
066 170 173 373
132 172 367
120 238 243 291 374
375
Orion
322 326 327 328 329
330
Panasonic
Pentax
112 117 430
078
Philco
086 132 183
Philips (Magnavox)
Pioneer
086 132 183 172
078 120 263
Portland
ProScan
Quartz
345
170 174
238 378
Quasar
112
RCA
078 132 141 170 172
173 174
Realistic
Samsung
Sansui
066 132 238 363
269 271 275 276 278
120 367 379
Sanyo
238 346 357 363
Scott
033 332 367
Sears
035 078 238 331 363
Sharp
066 075
Shintom
Signature 2000
Sony
367
066 170 173 373
056 058 060
Soundesign
Sylvania
132
086 132 141 183 184
322 324 420
Symphonic
Tandy
132
132 238
Tashiko
Tatung
331
243
Teac
132 243
Technics
Teknika
Thomas
TMK
086
132 331 359
132
338
Toshiba
Totevision
Unitech
033 035 078 081
172 331
172
Vector Research
291
- 8 -
Synergy.doc
Video Concepts
Wards
132 291
066 132 172 247 331
XR-1000
Yamaha
Zenith
367
132 243 291
058 120 122 128 132
435
DVD Setup Codes
Apex Digital
B144
Denon
193
146
201
227
203
DVD-Video
ECA
GE
Goldstar (LG)
Gradiente
Harmon Kardon
Hitachi
JVC
Kenwood
KLH
LG (Goldstar)
Magnavox
Marantz
Mitsubishi
Mintek
199
156
150
129
212
256
149
177
228
248
129
138
270
181
432
246
085
115
125
236
156
192
034
040
421
156
082
121
129
152
133
234
259
156 175
135 179 260
179
252
133
143
135 179 260
146
185
NAD
Onkyo
244
118
187
Panasonic
Pioneer
Proceed
RCA
Samsung
Sharp
121 124 431
188
224
076
059
225
077 079
061 436
Sony
Sylvania
Thomson
Toshiba
Yamaha
Zenith
237
085
124
133
087 113
210
135
Audio Setup Codes
Compact Disc
ADC
318
Akai
Aiwa
249 261
176
Carver
176
Crown
154
Denon
273
Fisher
230 274
308
315
Goldstar (LG)
Harman Kardon
JVC
297
Kenwood
Krol
131 176 274 289 299
176
LG (Goldstar)
Magnavox (Philips)
Mission
308
037 084 119 296
176
Mitsubishi
NAD
245 249
182 231 290
Nakamichi
NEC
264 319
235
NSM
176
Onkyo
300
Panasonic
Philips (Magnavox)
Pioneer
Quasar
184 266 437
037 084 119 296 433
116 127
184
Radio Shack
RCA
186 190 266 279 289
295
Sanyo
230 309
- 9 -
Synergy.doc
SAE
176
Scott
186
Sharp
288 289
Sony
067 292 293
Soundesign
STS
148 242 311 320
318
Sylvania
Teac
084
186
Technics
Toshiba
Yamaha
184 208 317
290
280
Receiver / Amplifier
Adcom
325
Aiwa
301
Akai
142
Bose
302 440
Carver
155 180
Denon
262 307
Everquest
Fisher
136
063 180
Fosgate Audionics
Goldstar (LG)
Harman Kardon
Hitachi
305
036
130 257 305 306
240
Jensen
140
JVC
114 241
Kenwood
LG (Goldstar)
Luxman
Magnavox
Marantz
NAD
063 277
036
281
080
282 283 284 285
286
Onkyo
126 171 304
Optimus
Panasonic
Parasound
Philips (Magnavox)
Pioneer
Quasar
142 229 321
032 074 438 441
323
080
123 137 251 298
032
Radio Shack
Realistic
RCA
229 267
226 268
439
Rotel
310
Sansui
283
Sanyo
195
Scott
272
Sharp
294
Sherwood
Sony
229 267
041 057 232 287 442
Soundesign
SSI
083 088 239 265
313
Taekwang
Teac
142
314 316
Technics
Wards
032
063
Victor
114 241
Yamaha
Zenith
145 254 303
036 083 088 239 265
8.
Code Number Read-Back
To identify the 3-digit setup codes stored under the Point and Press® programming method, follow these steps:
To identify the TV setup code…
1. Press [TV], then [OK] together until the [TV] button illuminates.
2. Press [INFO]. The [TV] button will “blink back” the code numbers, with a 1-second interval between each
digit of the code.
- 10 -
Synergy.doc
Example: For code “035”, the remote will blink 10 times, then 3 times, then 5 times.
To identify the 3-digit VCR code, press [VCR], then [OK] in step 1, then press [INFO].
To identify the 3-digit DVD code, press [DVD], then [OK] in step 1, then press [INFO].
To identify the 3-digit AUDIO code, press [AUDIO], then [OK] in step 1, then press [INFO].
9. ALL SmartKey®
Once you have programmed the remote to operate your electronic devices, you can press the [ALL] SmartKey® to
turn your Cable set-top terminal and TV on / off with one button press. You can also program the [ALL] button to
turn on / off additional electronic devices and / or tune your TV to its correct output channel.
Programming the [ALL] SmartKey®
1. Press [ALL], then [MENU] together until the [CBL] button illuminates.
2. Enter one of the following options on the keypad of the remote:
[0] - Turns on / off CBL + TV (default setting)
[1] - Turns on / off CBL + TV and tunes TV to output Channel 3.
[2] - Turns on / off CBL + TV and tunes TV to output Channel 2.
[3] - Turns on / off CBL + TV and tunes TV to output Channel 4.
[10] - Turns on / off CBL + TV + VCR + DVD
[4] - Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 3.
[5] - Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 2.
[6] - Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 4.
[11] - Turns on / off CBL + TV + VCR + DVD + AUDIO
[7] - Turns on / off CBL + TV + VCR + DVD + AUDIO and tunes TV to output Channel 3.
[8] - Turns on / off CBL + TV + VCR + DVD + AUDIO and tunes TV to output Channel 2.
[9] - Turns on / off CBL + TV + VCR + DVD + AUDIO and tunes TV to output Channel 4.
[12] - Turns on / off CBL + TV + AUDIO
[13] - Turns on / off CBL + TV + AUDIO and tunes TV to output Channel 3
[14] - Turns on / off CBL + TV + AUDIO and tunes TV to output Channel 2
[15] - Turns on / off CBL + TV + AUDIO and tunes TV to output Channel 4
3. As soon as you select an option, the [CBL] button will blink 3-times and go out.
Using the [ALL] SmartKey®
When pressing the [ALL] SmartKey®, be sure to keep the remote control aimed at your electronic devices until
your electronic devices turn on or / off.
Whenever the [ALL] SmartKey® is pressed, the mode of the remote control will automatically switch back to
Cable.
10. Volume Control
When you first program your remote, volume / mute are controlled through your TV (except AUDIO which defaults
to the AUDIO device). The volume control options in each mode of the remote are:
CBL
TV
VCR
DVD
TV (default), Cable or Audio.
TV (default), Cable or Audio.
TV (default), Cable or Audio.
TV (default), Cable or Audio.
- 11 -
Synergy.doc
AUDIO
AUDIO device (default), Cable or TV.
To control volume / mute through your Cable set-top terminal in the remote’s Cable mode…
1. Press [CBL], then [OK] together until the [CBL] button illuminates.
2. Press [VOL +], then [CBL] for Cable volume. The [CBL] button will blink 3-times and go out.
To return volume control to your TV, repeat step 1, then press [VOL +], then [TV] in step 2.
11. Channel Memory Button - [M1]
Your remote has 1 Channel Memory Button ([M1] - See Section 15) which can store up to 5 cable channels. This
button may come pre-set / labeled to channels selected by your cable operator. If this button has not been pre-set
by your cable operator, it can be programmed as follows:
Programming Channel Memory Button
To program the [M1] button to cable channels 1, 12, 123, 1234, 17, follow these steps:
1. Press [M1], then [CBL] together until the [CBL] button illuminates.
2. Enter each channel as follows (ex. assumes 4-digit channel format):
a. Enter 1st channel # - 0001.
b. Press [CH +] to advance to next channel # setting.
c. Enter 2nd channel # - 0012.
d. Press [CH +] to advance to next channel # setting.
e. Enter 3rd channel # - 0123.
f. Press [CH +] to advance to next channel # setting.
g. Enter 4th channel # - 1234.
h. Press [CH +] to advance to next channel # setting.
i. Enter 5th channel # - 0017.
3. Press [M1] to store the above channels. The [CBL] button will blink 3-times and go out. To store fewer
than 5 channels, you can press the [M1] button any time after entering a complete channel number.
Using Channel Memory Button
Using the above programmed channels as an example…
1. Press [M1] – Cable set-top terminal tunes to channel 0001.
2. Press [M1] again – Cable set-top terminal tunes to channel 0012.
3. Press [M1] again – Cable set-top terminal tunes to channel 0123.
4. Press [M1] again – Cable set-top terminal tunes to channel 1234.
5. Press [M1] again – Cable set-top terminal tunes to channel 0017.
6. Press [M1] again – Cable set-top terminal tunes to channel 1….repeat.
Whenever the Channel Memory button is pressed, the function of the transport buttons will automatically switch
back to Cable.
When pressing the Channel Memory Button, be sure to keep the remote control aimed at your Cable set-top
terminal to ensure the full channel numbers are received in their entirety.
If you are using your Synergy® V remote to operate a Cable set-top terminal other than the Motorola 62xx series
DVR model, you may only have to enter channels in a 3-digit format (ex. 012).
12. Input
This button changes the input source of your electronic devices. In the remote's Cable mode, this operates a Cable
- 12 -
Synergy.doc
function. In the remote's TV mode, this button changes the Input Source (Input 1, Input 2...) on your TV. In the
remote's VCR mode, this button changes the TV / VCR Input on your VCR.
You can program this button so that in the remote's Cable mode, [INPUT] will operate the Input function
on your TV or VCR, eliminating the need to change modes on the remote.
To program [INPUT] to operate your TV Input function in the remotes cable mode...
1. Press [INPUT], then [OK] together until the [CBL] button illuminates.
2. Press [TV]. The [CBL] button will blink 3-times and go out.
Note: You can also press [VCR] in step 2 above to operate the TV / VCR function on your VCR. Or press [CBL] to
return to the normal CBL Video Source function.
13. Reset
To reset your remote control to its factory default settings…
1. Press [CBL], then [OK] together until the [CBL] button illuminates.
2. Press [MENU], then [MENU] again. The [CBL] button will blink 3 times and go out.
Reset returns the ALL SmartKey®, Volume / Mute, Mode Lock™ features to their factory default settings.
14. Additional Programming Information, Troubleshooting, Terms
Additional Programming Information
1. The power / mode buttons will illuminate in slow-rotation (i.e. CBL Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL…)
while the remote is in a programming mode. In the absence of a keypress entry, the power / mode buttons will
stop illuminating after 45 seconds and the remote will exit the programming mode.
2. When programming the remote control using the [CH +] or [CH -] buttons (Power function) in the Point and
Press® Programming method, you may find a code that turns a device off but not back on. If this happens…
a. The correct code has not been found as you may have a code that operates some but not all of the
functions of your device. Continue pressing [CH +] until your device turn on.
OR
b. You may have gone past the correct matching code. Try pressing [CH -] one press at a time until you
find a code that turns your device back on.
3. When using the Point and Press® Programming method, you can also program your remote using buttons other
than the [CH +] or [CH -] as described in Section 5 as follows:
a. [VOL +] – to “go forward” through the codes using the “VOL +” function on your devices.
b. [VOL -] – to “go back” through the codes using the “VOL -“ function on your devices.
Note: When you find the correct code, the volume of the device being programmed will increase or
decrease.
c. [S] - to “go forward” through the codes using the “CH +” function on your devices.
d. [T] - to “go back” through the codes using the “CH –“ function on your devices.
Note: When you find the correct code, the channel of the device being programmed will increase or
decrease.
e. [XX] - to “go forward” through the codes using the “Fast Forward” function on your devices.
f. [WW] - to “go back” through the codes using the “Rewind” function on your devices.
- 13 -
Synergy.doc
Note: When you find the correct code, the fast-forward or rewind function of the device being programmed
will be performed. To simplify programming using these buttons, insert a VHS tape or DVD in the device
being programmed.
You can also program your remote using the other available functions as follows:
a. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL
Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL…).
b. In this order, carefully press [0], [0], [0], [CH+] and [VOL+]. The power / mode buttons illuminate in slow-
rotation (i.e. CBL Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL…).
c. You can now program your remote using the [CH+], [CH -], [VOL+], [VOL -], [▲], [T], [FFWD], [REW],
[PLAY], [STOP], [REC], [PAUSE], [LAST], [FAV], [0] - [9] buttons. When you find the correct code, the
function associated with the selected button will be performed.
4. Your remote is equipped with a Point and Press® Programming label on the back of its case. This will help
you quickly program the remote without using codes.
Troubleshooting / Tips
1. If the same button is pressed and held for 45-seconds, your remote control will turn itself off automatically.
This extends the battery life should the remote become lodged under or between heavy objects, for example
sofa cushions.
2. If you have a TV that’s operated by remote control, it is recommended that you plug it directly into a wall
outlet instead of the cable set-top terminal.
3. If you have any questions concerning the brand, model or operation of your cable set-top terminal, contact
your cable operator.
Frequently Used Terms
AUDIO Devices - Audio receivers, amplifiers, CD players that you can program your remote to operate.
DVR - Digital Video Recorder.
Default Setting – How your remote is set when you receive it from your cable operator.
Electronic Components / Devices - The various electronics device the remote is designed. These include cable
set-top terminals, TVs, VCRs, DVDs, audio-video receivers, amplifiers and CD players.
Fast-Rotation - The power / mode buttons will illuminate in a fast sequence (i.e. CBL Æ TV Æ VCR Æ DVD Æ
AUDIO Æ CBL…) repeated every 1/3 second. Fast-rotation occurs when the remote is receiving keypresses to
program it to your electronic devices.
Mode - The device the remote is set to operate (ex. Cable, TV, VCR, DVD, Audio)
PIP – Picture-in-picture functionality through your Cable set-top terminal.
Program (Setup) – The process of teaching your remote control to operate your electronic devices.
Slow-Rotation - The power / mode buttons illuminate in a slow sequence (i.e. CBL Æ TV Æ VCR Æ DVD Æ AUDIO
Æ CBL…) repeated every 1 second. Slow-rotation illumination occurs when the remote is in the programming
mode, waiting for the next entry on the keypad of the remote.
TV Output Channel - The channel your TV needs to be set on for proper Cable reception (most often TV channel 3,
but may be TV channel 2 or 4). If you have any questions concerning your TV output channel, contact your cable
operator. Or, with your cable set-top terminal turned on, try setting your TV to channel 2, 3 or 4 to obtain a clear
picture.
- 14 -
Synergy.doc
Transport Functions - These are the [STOP], [PLAY], [FWD], [REW], [PAUSE] and [REC] buttons. In the remote
control's Cable mode, these buttons operate your Cable set-top features. In the remote control's VIDEO mode,
these operate your VCR or DVD functions.
VIDEO Devices - VCR or DVD players.
Device Setup Codes
If you find that the setup codes listed above do not operate your devices, it is possible your remote was
manufactured before the revision date printed on this Instruction Manual. If this occurs, contact your cable operator
and request a newer version of your remote control.
© 2004, Contec Corporation
Rev. 09/04
Point and Press®, Memory Guard®, SmartKey® and Synergy® are registered trademarks of Contec Corporation
Explorer® is a registered trademark of Scientific-Atlanta, Inc.
Voyager® is a registered trademark of Pioneer New Media Technologies, Inc.
U.S. Patent 6,507,306
- 15 -
Synergy.doc
15. Using Your Synergy® V - Universal / DVR Remote Control
Important: The following diagram shows how to use the buttons on your remote control to operate the DVR and
PIP functions of the Motorola DCT 62xx series DVR set-top terminal. To access these functions, set the remote
control to its Cable mode by pressing the [MODE] button, followed by the [CBL] button.
Illuminate / select electronic device
being operated. Press Mode, then…
CBL - for Cable mode
CBL & TV on / off
(programmable)
TV - for TV mode
Individual device on / off power
VCR - for VCR mode
DVD - for DVD mode
AUDIO - for Audio mode
Access on-screen display
for cable device
Access cable guide
Display channel / program
information
Moves through on-screen display or
cable guide menu (S,T,X,W)
Move ↑ / ↓ through on-screen
displays, cable guide
Access on-screen display for cable
device
Selects highlighted on-screen
or cable guide choice
Functions set by cable operator
(A, B, C)
Exit any on-screen display
DayW / X in cable guide
Recall pre-selected favorite
channels
Display Help screen on cable device
Return to last selected channel
Replay previous few seconds of
program (DVR set-top terminals
only)
Display live TV programming
(DVR set-top terminals only)
Listing of recorded programs (DVR
set-top terminals only)
Fast-forward DVR, VCR, DVD
Play DVR, VCR, DVD
Record DVR, VCR
Pause DVR, VCR, DVD
Digital Music
Rewind DVR, VCR, DVD
Stop DVR, VCR, DVD
Change viewing aspect of cable
device
PIP on / off
Move PIP screen
Swap PIP & and main screen
Selects video source
PIP channel +/-
M1
Access Pay-Per-View
programming where available
Channel memory button (may be
labeled or pre-set by cable operator)
Access Video-On-Demand
programming where available
- 16 -
|