Coleman Tent 2000005748 User Manual

®
ELITE WEATHERMASTER TENT  
MODEL 2000005748  
Before you begin  
Fig. 6  
Curved Ridge Poles with Red Markings in center sleeves  
Read all instructions before set up.  
Select a level site clear of rocks, branches, and other hard or sharp  
objects, to install your tent.  
WARNING: Keep clear of overhead power lines.  
Do not set up your tent under trees because of potential lightning strikes or  
falling tree limbs in inclement weather.  
Secure with all stakes and guylines provided to prevent property damage  
or personal injury.  
6. Rotate all eight Leg Poles upright and insert pin on each  
web loop at the side locations as shown. (Fig. 7 & 7A)  
For best results in windy conditions, position narrow end of tent into the wind.  
Enlist the help of at least one other person to assist you when it is time to  
assemble the tent.  
7A  
Pin  
Pole Descriptions  
Pole  
Pole  
Description  
Qty. Repair Kit  
Replacement Kit  
Long Leg Pole, steel  
(w/ red marking)  
4
4
N/A  
N/A  
5010000754  
5010000755  
Short Leg Pole, steel  
Curved Ridge Pole, steel  
(w/ red marking)  
Curved Ridge Pole, steel  
Awning Pole, black,  
fiberglass, metal tips  
Door Pole, long, thin, black,  
fiberglass, rubber tips  
Vert. Door Pole, short, black,  
fiberglass, rubber tips  
2
2
N/A  
N/A  
5010000756  
5010000757  
2
1
1
5010000543  
5010000543  
5010000543  
5010000545  
5010000545  
5010000545  
Fig. 7  
7. Locate the plastic hooks at sides and  
corners of tent, then snap onto Leg Poles to  
attach. (Fig. 8)  
Self-Rolling Window Spring Descriptions  
Color Code Description  
Qty.  
1
Replacement Part No.  
5010000624  
Fig. 8  
Fig. 9  
Red  
Yellow  
Green  
Orange  
2
1
2
5010000626  
5010000627  
5010000628  
8. To stretch tent to finished size:  
Push in button on Leg Pole while  
twisting lower Leg Pole section  
counterclockwise (Fig.9);  
Upper  
Leg Pole  
Section  
CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury.  
Pull up on top Leg Pole section until  
tent is taut;  
Twist the lower Leg Pole clockwise  
until the button locks into the center or  
lowest hole;  
Keep out of reach of children.  
Button  
Center Hole  
Lower Hole  
To Set Up Tent  
1. Unfold tent and spread out on a clean, level surface with the door facing  
Lower  
the desired direction. Unzip doors. (Fig. 1)  
Leg Pole  
Fig. 1  
Section  
Repeat on remaining Leg Poles.  
9. Insert plastic stakes through web straps located on  
both sides of tent, then drive in to secure. (Fig. 10)  
NOTE: It may be necessary to remove metal stakes  
through web straps at side of tent and screen room,  
pull tent taut, and drive in stakes to secure.  
Door  
2. Pull four corners of tent taut, then secure by driving  
stakes through web loops at an angle for better  
anchoring. (Fig. 2)  
Fig. 10  
Hinged, Rigid Door  
1. Assemble Vertical Door Pole (shorter black pole with plastic tips); then insert  
through zippered vertical pole sleeve on hinged side of door. (Fig. 11)  
2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to  
form a slight bow, then insert other tip of pole into top hinge. Zip up verti-  
cal pole sleeve. (Fig. 12 & 13)  
3. Assemble Door Pole (longer black pole with plastic cap tips); then insert  
into zippered pole sleeve at top of door. (Fig. 14)  
4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow,  
then insert other tip of pole into the bottom hinge. (Fig. 15)  
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)  
Fig. 2  
3. Assemble four, steel, shock-corded, curved  
Ridge Poles. Insert Ridge Poles (with red  
marking) into center sleeves on top of tent with  
the red trim (Fig. 3). Insert the remaining curved  
Ridge Poles into the other two sleeves on top of  
tent.  
Fig. 3  
Ridge Pole  
with Red  
Marking  
Sleeve  
with Red  
Trim  
4. Assemble eight, steel, shock-corded, Leg Poles.  
Push down on steel button on tapered end and  
insert into end with four holes.  
Fig. 11  
Fig. 12  
Fig. 13  
Vertical Pole  
Sleeve  
Button in third hole  
NOTE: Make sure steel button locks into third  
hole on pole as shown. (Fig.4)  
Fig. 4  
Door Hinge  
5. Insert curved end of Leg Poles  
(with red marking) into the  
Ridge Pole with  
Red Marking  
ends of the Ridge Pole (with  
Fig. 15  
Fig. 14  
red marking). Insert curved  
end of remaining short Leg  
Poles into the ends of the  
remaining Ridge Poles.  
(Fig. 5 & 6)  
Top  
Door  
Sleeve  
with Red  
Trim  
Pole  
Sleeve  
Curved End of  
Long Leg Pole  
Hinge  
Fig. 16  
Fig. 5  
 
(continued on other side)  

Code Alarm Automobile CA 630 User Manual
Cooper Lighting Indoor Furnishings 12X HZB User Manual
Cooper Lighting Indoor Furnishings 152 User Manual
Cooper Lighting Indoor Furnishings WBI User Manual
Craftsman Snow Blower 536881851 User Manual
DXG Technology Camcorder DXG A85V HD User Manual
Dynex Mouse DX WLM 1401 BK DX WLM1401 SV DX WLM1401 BU User Manual
EdgeStar Air Conditioner AP410HS User Manual
Furman Sound Power Supply PL PRO E II User Manual
Garmin Computer Monitor 906 2000 00 User Manual