®
ELITE SUNDOME 6 TENT
MODEL 2000001585
7. Stretch corners and sides of tent until floor is taut then hammer
Before you begin
stakes through loops to secure. (Fig. 3B)
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
Fig. 3
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Pole Descriptions
Door
Pole
Pole
Pole
Description
Qty. Dia.
Repair Kit Replacement Kit
Main Poles, long, black
2
11mm 5010000539 5010000549
Rainfly Pole, black
w/metal tips
1
1
1
11mm 5010000539 5010000549
Vertical Door Pole, black,
short w/rubber tips
6.3mm 501000543
6.3mm 501000543
501000545
501000545
Door Pole, black,
long w/rubber tips
3A
3B
Self-Rolling Window Spring Descriptions
Color Code Description
Qty.
Length Replacement Part No.
Green
Orange
1
1
550mm
670mm
5010000626
5010000628
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips);
then insert through zippered vertical pole sleeve on hinged side of
door. (Fig. 4)
CAUTION: “Springs” may have sharp edges. Handle with care to avoid
injury. Keep out of reach of children.
2. Insert end of Vertical Door Pole into bottom hinge plate, apply
pressure to form a slight bow, then insert other tip of pole into top
hinge. Zip up vertical pole sleeve. (Fig. 5 & 6)
3. Assemble Door Pole (longer black pole with plastic cap tips); then
insert into zippered pole sleeve at top of door. (Fig. 7)
4. Insert end of Door Pole into top hinge plate, apply pressure to form
a bow, then insert other tip of pole into the bottom hinge. (Fig. 8)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 9)
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the door
facing the desired direction. (Fig. 1)
2. Assemble two main tent poles by interlocking the longer, black
shock-corded, poles.
3. Insert both, long, black poles through sleeves in top of tent as
shown. (Fig. 1)
Fig. 4
Fig. 5
Fig. 6
Vertical Pole
Sleeve
Fig. 1
Door Hinge
Long, Black,
Shock-corded
Main Poles
Fig. 8
Fig. 7
Door
Top
Door
Hinge
Pole
Sleeve
Fig. 9
Front of Tent
To Attach Rainfly
1. Assemble longer interlocking shock-corded rainfly pole.
2. Unfold rainfly. Locate the sleeve, along front edge, and the hook &
loop fasteners on the underside of Rainfly.
3. Drape Rainfly over tent. Make sure the sleeve is centered over the
door and the hook & loop fasteners, on the seams on underside of
the Rainfly, are
4. Insert one end of each black
pole into pins in front corners of
tent. (Fig. 2)
Rainfly
Pole
positioned over
the black main
poles.
Rainfly
Sleeve
4. Slide rainfly pole
through sleeve at
front of the Rainfly.
(Fig. 10)
Fig. 2
Door
5. Go to opposite end of each pole and gradually apply pressure to the
pole forming an arch. Insert the pin into the pole end at the corners
of tent. (Fig. 3)
6. Attach frame clips along edges of tent to black main poles.
(Fig. 3A)
(continued on
other side)
Fig. 10
|