Chicago Electric Portable Generator 94678 User Manual

2.5 Horsepower  
Gas enGine Generator  
94678  
installation and operation instructions  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
Distributed exclusively by  
®
Harbor Freight Tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
to preVent serious injury, read and understand  
all warninGs and instructions before use.  
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
for technical questions or replacement parts, please call 1-800-444-3353.  
 
specifications  
Generator Type  
Wattage  
Brushless / Revolving Field / Self Exciting / Two Pole / Single Phase  
1,000 / 1,050 (Continuous-Rated/Peak)  
Electrical Output  
110/120 V~, 60 Hz  
about 18 V (12 V battery charging)  
Electrical Supply  
120 V~, 3-Prong Grounded Duplex Receptacle  
with 10 Amp Resettable Circuit Protection  
12 V Battery-charging Output* with 10 Amp Resettable Circuit Protection  
*Only for use with included power cord for 12 V battery charging.  
Voltmeter  
0-300 V~  
57 lb.  
Total Weight  
Engine Type  
2.5 HP / Unleaded Gasoline Powered / Recoil Start / 4-Cycle / Air-Cooled  
98 cc Displacement / Low Oil Shutdown / CARB and EPA Certified  
Estimated Run Time 5.5 Hours on full tank  
Engine Oil Type  
SAE 10W-30 (for general, all temperature use)  
Engine Oil Capacity 0.47 Quart (0.45 Liter)  
Fuel Tank Capacity  
Spark Plug Gap  
about 1.2 Gallons  
0.6-0.7 mm  
Recommended  
Spark Plugs  
L6RTF, BM4A, BMR4A (NGK)  
only use these types. An incorrect spark plug may damage the engine.  
Bore x Stroke  
52 x 46 mm  
PTO Shaft Rotation Counterclockwise Facing The Shaft  
WARNING: This product requires oil and fuel to be added before  
starting. Attempting to start the engine without oil WIll ruin the engine  
and VOID the warranty!  
caution: This generator is not intended to power sensitive electronic equipment without the  
addition of an appropriate line conditioner (not included or sold by Harbor Freight Tools).  
The Emission Control System for this generator’s engine is warranted for standards  
set by the U.S. Environmental Protection Agency and by the California Air Resources  
Board (also known as CARB). For warranty information, refer to the back two pages of  
this manual.  
save this Manual  
You will need this manual for the safety warnings and precautions, assembly, oper-  
ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.  
Keep your invoice with this manual. Write the invoice number on the inside of the front  
cover. Write the product’s serial number in the back of the manual near the assembly dia-  
gram, or write month and year of purchase if product has no number. Keep this manual  
and invoice in a safe and dry place for future reference.  
REV 07g  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 3  
 
General safety rules  
warninG!  
read and understand all instructions  
failure to follow all instructions listed below may result in  
electric shock, fire, and/or serious injury.  
saVe tHese instructions  
work area  
1.  
2.  
keep your work area clean and well lit. Cluttered benches and dark areas invite  
accidents.  
do not operate equipment in explosive atmospheres, such as in the presence  
of flammable liquids, gases, or dust. Equipment create sparks which may ignite  
the dust or fumes.  
3.  
1.  
keep bystanders, children, and visitors away while operating a equipment.  
Distractions can cause you to lose control. Protect others in the work area from  
debris such as chips and sparks. Provide barriers or shields as needed.  
electrical safety  
avoid body contact with grounded surfaces such as pipes, radiators, ranges,  
and refrigerators. There is an increased risk of electric shock if your body is  
grounded.  
2.  
3.  
do not expose equipment to rain or wet conditions. Water entering a equipment  
will increase the risk of electric shock.  
do not abuse power cords. never use a power cord to pull a plug from the  
outlet. keep all power cords away from heat, oil, sharp edges, or moving  
parts. replace damaged power cords immediately. Damaged Power Cords  
increase the risk of electric shock.  
personal safety  
1.  
2.  
stay alert. watch what you are doing, and use common sense when operating  
a equipment. do not use a equipment while tired or under the inuence of  
drugs, alcohol, or medication. A moment of inattention while operating equipment  
may result in serious personal injury.  
dress properly. do not wear loose clothing or jewelry. contain long hair.  
keep your hair, clothing, and gloves away from moving parts. Loose clothes,  
jewelry, or long hair can be caught in moving parts. Be aware that when engine  
parts are moving fast they cannot be seen clearly.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 4  
 
3.  
remove adjusting keys or wrenches before turning the equipment on. A  
wrench or a key that is left attached to a rotating part of the equipment may result  
in personal injury.  
4.  
5.  
do not overreach. keep proper footing and balance at all times, especially  
when starting the equipment.  
use safety equipment. always wear eye protection. Dust mask, nonskid safety  
shoes, hard hat, or hearing protection must be used for appropriate conditions. Al-  
ways wear ANSI-approved safety goggles when using or performing maintenance  
on this equipment.  
equipMent use and care  
1.  
do not force the equipment. use the correct equipment for your application.  
The correct equipment will do the job better and safer at the rate for which it is de-  
signed. Do not force the equipment and do not use the equipment for a purpose  
for which it is not intended.  
2.  
3.  
do not use the equipment if the power switch does not turn it on or off. Any  
equipment that cannot be controlled with the Power Switch is dangerous and must  
be replaced.  
turn the power switch and the fuel supply to off and unplug the spark plug  
wire before making any adjustments, changing accessories, or storing the  
equipment. Such preventive safety measures reduce the risk of starting the equip-  
ment accidentally.  
4.  
5.  
6.  
store idle equipment out of reach of children and other untrained persons.  
Equipment is dangerous in the hands of untrained users.  
Maintain equipment with care. Do not use a damaged equipment. Tag damaged  
equipment “Do not use” until repaired.  
check for misalignment or binding of moving parts, breakage of parts, and  
any other condition that may affect the equipments operation. if damaged,  
have the equipment serviced before using. Many accidents are caused by poorly  
maintained equipment.  
7.  
1.  
use only accessories that are recommended by the manufacturer for your  
model. Accessories that may be suitable for one piece of equipment may become  
hazardous when used on another piece of equipment.  
serVice  
equipment service must be performed only by qualied repair personnel.  
Service or maintenance performed by unqualified personnel could result in a risk  
of injury.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 5  
 
2.  
3.  
when servicing a equipment, use only identical replacement parts. follow  
instructions in the “Inspection, Maintenance, And Cleaning” section of this  
manual. Use of unauthorized parts or failure to follow maintenance instructions  
may create a risk of electric shock or injury.  
do not alter or adjust any part of the equipment or its engine that is sealed  
by the manufacturer or distributor. only a qualied service technician may  
adjust parts that may increase or decrease governed engine speed.  
specific safety rules  
1.  
2.  
Maintain labels and nameplates on the generator. These carry important infor-  
mation. If unreadable or missing, contact Harbor Freight Tools for a replacement.  
warninG! people with pacemakers should consult their physician(s) before  
using this product. Electromagnetic fields in close proximity to a heart pacemaker  
could cause interference to or failure of the pacemaker.  
3.  
avoid body contact with fuels, oils, and lubricants used in the Generator. If  
swallowed, seek medical treatment immediately. Do not induce vomiting if fuel is  
swallowed. For skin contact, immediately wash with soap and water. For eye con-  
tact, immediately flush eyes with clean water.  
4.  
5.  
prolonged exposure to noise levels above 85 dba is hazardous to hearing.  
Always wear ANSI-approved hearing protection when operating or working around  
the Generator when it is running.  
lifting/transport precautions. Never lift the Generator using the engine or al-  
ternator lifting lugs. Connect lifting equipment only to the Frame of the Generator.  
Before lifting the Generator, ensure the lift rigging and supporting structure are in  
good condition, and are rated to lift such a load. Keep all personnel away from the  
suspended generator while relocating.  
6.  
warninG! Some dust created by power sanding, sawing, grinding, drilling, and  
other construction activities, contain chemicals known (to the State of California)  
to cause cancer, birth defects or other reproductive harm.  
Some examples of these chemicals are:  
• Lead from lead-based paints.  
• Crystalline silica from bricks and cement or other masonry products.  
• Arsenic and chromium from chemically treated lumber.  
Your risk from these exposures varies, depending on how often you do this type of  
work. To reduce your exposure to these chemicals: work in a well-ventilated area,  
and work with approved safety equipment, such as those dust masks that are spe-  
cially designed to filter out microscopic particles.  
(California Health & Safety Code § 25249.5, et seq.)  
REV 07l  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 6  
 
installation precautions  
1.  
ensure installation meets all applicable safety, and local and national electri-  
cal codes. Have installation performed by a qualified, licensed electrician and  
building contractor.  
2.  
3.  
all electrical work, including the earth-ground connection, should be com-  
pleted by a licensed electrician.  
if the generator is installed indoors, exhaust fumes must be piped  
out of the building using leak-free, heat-resistant piping. use the  
Generator only in well ventilated outdoor areas. carbon monoxide  
fumes are a colorless, odorless gas that, if inhaled, can cause seri-  
ous injury or death. Pipes and silencer should not use any flammable  
materials, nor should they be installed near the same. Generator exhaust fumes  
must be within legal limits.  
4.  
5.  
if the generator is installed outdoors, it must be weatherproofed and should  
be soundproofed. It should not be run outdoors without protection to the Generator  
and wiring conduit. Install sound- and weather-proofing only when it is not raining  
or snowing to avoid trapping moisture within the Generator’s area.  
the supporting floor/ground surface should be level, and strong enough to  
safely hold the weight of the Generator. If the floor/ground surface is not level,  
strong cross members should be placed under the full length of the Generator  
Frame at its low side.  
6.  
1.  
for trailer installation, the Generator should be mounted on the center point  
of the trailer, over the wheels.  
fire and eXplosion precautions  
Gasoline fuel and fumes are ammable, and potentially explosive. Use proper  
fuel storage and handling procedures. Always have multiple ABC class fire extin-  
guishers nearby.  
2.  
3.  
keep the Generator and surrounding area clean at all times.  
when spills of fuel or oil occur, they must be cleaned up immediately. Dispose  
of fluids and cleaning materials as per any local, state, or federal codes and regula-  
tions. Store oil rags in a covered metal container.  
4.  
5.  
never store fuel or other ammable materials near the Generator.  
do not smoke, or allow sparks, flames or other sources of ignition around the  
engine and fuel tank. Keep grounded conductive objects, such as tools, away  
from exposed, live electrical parts and connections to avoid sparking or arcing.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 7  
 
6.  
7.  
do not rell the fuel tank while the engine is running or while the engine is  
still hot. Do not operate the Generator with known leaks in the fuel system.  
excessive buildup of unburned fuel gases in the exhaust system can create  
a potentially explosive condition. This buildup can occur after repeated failed  
start attempts, valve testing, or hot engine shutdown. If this occurs, open exhaust  
system drain plugs, if equipped, and allow the gases to dissipate before attempting  
to restart the Generator.  
8.  
any separate Generator fuel storage facility must be built/installed in full  
compliance with all relevant local, state, and federal regulations.  
MecHanical precautions  
do not operate the Generator with safety guards removed. While the Generator  
is running, do not attempt to reach around the safety guards for any reason.  
electrical precautions  
1.  
all connections and conduits from the Generator to the load must only be  
installed by trained and licensed electricians, and in compliance with all  
relevant local, state, and federal electrical codes and standards, and other  
regulations where applicable.  
2.  
3.  
4.  
the Generator must be earth-grounded in accordance with all relevant electri-  
cal codes and standards before operation.  
do not attempt to connect or disconnect load connections while standing in  
water, or on wet or soggy ground.  
insulate all connections and disconnected wires. Do not touch electrically en-  
ergized parts of the Generator and interconnecting cables or conductors with any  
part of the body, or with any non-insulated conductive object.  
5.  
connect the generator only to a load or electrical system (110/120 volt) that  
is compatible with the electrical characteristics and rated capacities of the  
Generator.  
6.  
7.  
before servicing equipment powered by the Generator, disconnect the equip-  
ment from its power input.  
keep all electrical equipment clean and dry. Replace any wiring where the  
insulation is cracked, cut, abraded or otherwise degraded. Replace terminals that  
are worn, discolored, or corroded. Keep terminals clean and tight.  
8.  
9.  
keep access doors on enclosures closed and locked when access is not  
required.  
keep all electrical cords away from moving parts on the generator.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 8  
 
10.  
this Generator provides raw,unregulated output to the battery charging outlet.  
Incorporating an inline regulator is strongly recommended while charging and the  
charging process must be monitored at all times. The battery charging output must  
not be used to power any other device or charge any other type of battery without  
a proper regulating device.  
installation instructions  
1.  
2.  
prior to powering tools and equipment, make sure the Generators rated watt-  
age capacity (1000 w) is adequate to supply all electrical loads that the unit  
will power. If powering exceeds the Generator’s capacity, it may be necessary  
to group one or more of the tools and/or equipment for connection to a separate  
Generator.  
Electrical and other permits may be required for the installation of emergency power  
systems. Investigate the local building and electrical codes before installing this  
unit. Installation must be completed by licensed contractors.  
General location  
1.  
2.  
It is recommended to locate and install the Generator outdoors where cooling air  
is readily available.  
Install the Generator so that the air inlets and outlets are not blocked by obstruc-  
tions such as bushes, trees, or snow drifts. Locating it in the path of heavy winds  
or snowdrifts may require the placement of a barrier for protection. The air inlet, in  
normal weather conditions, should face the prevailing wind direction.  
3.  
4.  
5.  
6.  
Install the Generator on a concrete slab or other area where rain drainage or flood  
waters can not reach it.  
Generator placement should allow four feet of access to all sides for mainte-  
nance.  
Place the Generator as close as possible to the electrical tools and equipment be-  
ing powered to reduce the length of extension cords.  
If the Generator in located indoors the Engine exhaust must be ventilated to the  
outdoors using leakproof, heat resistant, flexible, metal, flex tubing.  
GroundinG tHe Generator  
note: It is recommended that only a trained and licensed electrician perform this procedure.  
Connect a #6 AWG grounding wire (not included) from the Grounding Point (55a)  
on the Generator to a grounding rod (not included) that has been driven at least 24  
inches deep into the earth. The grounding rod must be an earth-driven copper or  
brass rod (electrode) which can adequately ground the Generator.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 9  
 
Generator control illustrations  
fuel  
Meter (1a)  
on/off  
switch (52a)  
circuit  
protectors  
dc (59a) ac (53a)  
ac outlets pilot lamp  
air filter cover (67) transparent  
to show controls underneath.  
(54a)  
(56a)  
choke  
control (80) plug (24)  
oil drain  
fuel Valves recoil start battery charging dipstick Voltmeter  
(9a, 81) Handle (64) outlet (57a) (28) (58a)  
Grounding  
point (55a)  
Before setting up or using the generator, familiarize yourself with the locations of  
the controls and adjustments as shown above.  
operation instructions  
note: For additional information regarding the parts listed in the following pages, refer to  
the assembly diagrams on pages 16 and 18 and the Generator control illus-  
trations above.  
pre-start checks:  
1.  
2.  
Check to make sure the Engine’s Power Switch (52a) is in its “offposition.  
iMportant! prior to rst using the Generator, the engine Must be lled  
with approximately 1/2 (0.47) quart of a high quality sae 10w-30 grade engine  
oil. To do so, unscrew and remove the Engine’s Oil Dipstick (28) located at the  
bottom of the Engine Crankcase. Fill the Engine’s Crankcase until the oil level is  
up to the upper marked line on the Dipstick. Then, screw the Dipstick back into  
the Oil Fill Hole.  
3.  
Before use, remove the FuelTank Cap (2a) and fill the FuelTank (8a) with unleaded  
gasoline. Then, replace the Fuel Tank Cap.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 10  
 
to start the engine:  
1.  
Make sure the electrical tools/equipment that will be used are not plugged in to  
the Generator.  
2.  
Turn on the Fuel Valves (9a, 81). Turn the Valve (9a) under the fuel tank to the  
vertical ON position and swing the Valve (81) on the carburetor behind the Air Filter  
right to the ON position.  
3.  
4.  
5.  
Close the Choke Control (80), swinging it to the left.  
Turn the ON/OFF Switch (52a) to its “ON” position.  
Hold the Start Handle (64) loosely and pull it slowly several times to allow the gaso-  
line to flow into the Engine’s carburetor. Then hold the Start Handle firmly and pull  
the rope hard and fast. Pull the rope all the way out, using two hands if necessary.  
If necessary pull the rope several times until the Engine starts. The red Pilot Lamp  
(56a) will illuminate while the generator is able to supply power.  
6.  
Allow the Engine to run for several seconds. Open the Choke Control (80) swing-  
ing it to the right.  
to power 110/120 Volt ac tools and equipment:  
1.  
prior to powering tools and equipment, make sure the Generators rated watt-  
age capacity (1000 w) is adequate to supply all electrical loads that the unit  
will power. If powering exceeds the Generator’s capacity, it may be necessary  
to group one or more of the tools and/or equipment for connection to a separate  
Generator.  
2.  
Only start the Generator with no loads attached. Once the Generator is running,  
simply connect the Power Cords of 110/120 volt AC powered tools and equipment  
into the 110/120 volt AC Outlets (54a).  
note: The Generator features an AC Circuit Protector (53a) to protect the AC  
circuit in case of an overload. Should an overload occur the Breaker will “trip” to  
its “offposition, causing the Generator to automatically shut down and the Pilot  
Light (56a) on the control panel will shut off to show that the Circuit Protector (53a)  
has been tripped. For details on preventing this problem, refer to Step #1 above in  
this section. Then, reset the circuitry system by pressing on the Circuit Protector.  
3.  
4.  
When finished using the Generator, turn the ON/OFF Switch (52a) to its “off”  
position. Turn the Fuel Valves (9a, 81) to their “offpositions. Then, disconnect  
all electrical powered tools and equipment from the Generator’s 110/120 volt AC  
Outlets (53a).  
After the Engine and Generator have completely cooled, store the Generator in a  
safe, clean, dry location (if not already installed in one).  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 11  
 
to charge 12 V lead-acid type batteries:  
note: lead-acid batteries can be hazardous. Carefully follow all instructions, safety  
precautions, and charging procedures as included with the battery you will recharge.  
batteries contain corrosive acid that can cause blindness or severe injury;  
always wear splash-resistant ansi-approved safety goggles and work gloves  
when handling batteries. Also, have a nearby area with water and baking soda  
available to allow you to wash quickly in the event of an emergency. Wash thor-  
oughly after working on or near batteries.  
1.  
Only start the Generator with no loads attached. Once the Generator is running,  
with the Charging Plug (60a) disconnected, connect the Charging Battery Clamps  
(60a) to the terminals (red clamp to positive, + terminal, and black clamp to negative,  
terminal) of the 12 V lead-acid battery to be charged if a regulator is not available.  
This Generator provides raw output to the battery charging outlet that is not regulated;  
incorporating an inline regulator is strongly recommended while charging.  
2.  
To start the charging process, connect the Charging Plug (60a) to the Battery Charg-  
ing Outlet (57a). Do not leave the battery unattended while it is charging.  
note:The Generator features a DC Circuit Protector (59a) to protect the DC circuit  
in case of an overload. Should an overload occur the Breaker will “trip” to its “off”  
position, causing the Generator to automatically shut down and the Pilot Light (56a)  
on the control panel will shut off to show that the Circuit Protector (59a) has been  
tripped. This problem may be caused by a defective battery, a large or high capacity  
battery that needs to be charged by another means, or other problems. Reset the  
circuitry system by pressing on the Circuit Protector.  
3.  
4.  
Periodically disconnect the Charging Plug (60a) and check the battery’s voltage.  
stop charging the battery when the batterys voltage reaches the manufac-  
turers recommended voltage (typically 13.5 V or less). overcharging can  
result in fire, eXplosion, or serious personal injury. If the battery is  
not charged enough, reconnect the Charging Plug (60a).  
Disconnect the plug from the generator’s charging outlet first, then disconnect the  
clamps from the battery.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 12  
 
inspection, Maintenance, and cleaninG  
(see maintenance chart on next page.)  
1.  
2.  
warninG! Make sure the Power Switch of the generator is in its “OFF” posi-  
tion, that the engine has cooled, and that all loads are unplugged from the electrical  
outlets before performing any inspection, maintenance, or cleaning procedures.  
before eacH use, inspect the general condition of the generator. Check for  
loose screws, misalignment or binding of moving parts, cracked or broken parts,  
damaged electrical wiring, and any other condition that may affect its safe operation.  
If abnormal noise or vibration occurs, have the problem corrected before further  
use. do not use damaged equipment.  
3.  
4.  
to cleantHe air filter: While wearing a NIOSH-Approved dust mask/respi-  
rator, remove the Air Filter Cover (67) and remove the Foam Filter (69) underneath.  
If it is ragged or has holes, it will need to be replaced. Rinse the filter out by hand  
with mild soap and water. Allow it to dry thoroughly before replacing it and reas-  
sembling the Air Filter Cover (67).  
to reMoVe tHe spark pluG:  
warninG! to access the spark plug, the fuel tank (8a) must be removed.  
carefully make sure that the engine is thoroughly cool,that no ignition sources  
(including lit cigarettes) are nearby, that rags for cleaning up spills and a  
class abc fire extinguisher is nearby, and that you have a suitable place to  
temporarily put the gas tank during work.  
a. First, make sure that the Fuel Valves (9a, 81) are both turned to their OFF posi-  
tions. Secure the Fuel Valve (9a) under the Fuel Tank closed using a string or  
cable tie if possible.  
b. Have a rag ready to promptly clean up the small amount of fuel that will spill and  
disconnect the fuel line from the Fuel Valve (9a) under the Fuel Tank (8a). Use  
a small cap to cover the end of the fuel valve to prevent debris from entering.  
c. Remove the four Bolts (4a) and other hardware from the corners of the FuelTank  
(8a). Make sure to note the order of the hardware that secures the Fuel Tank to  
the Frame – it is important that the fuel tank is reinstalled in the same fashion.  
d. Gently remove the Fuel Tank and set it aside without tipping it, being careful not  
to damage the Fuel Valve under the Tank.  
e. Now you have access to remove the Spark Plug (44) without difficulty. Care-  
fully check that the spark plug and wire are both in good condition and securely  
attached before reassembly.  
f. Reassembly is the reverse of the earlier steps. Take note that the Fuel Tank  
must be reinstalled with the Fuel Gauge in the same orientation as originally  
(see illustrations on page 9). The fuel tank should fit in place without contacting  
any engine or alternator components.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 13  
 
Maintenance cHart  
refer to a small engine service manual for procedures not explained in this manual. if you are uncertain about your ability  
to successfully and safely perform any procedure below, service should be performed by a qualied mechanic.  
before/  
after each  
use  
every 3  
Months or Months or  
50 hours  
every 6  
Monthly or  
20 hours  
yearly or  
300 hours  
Maintenance type  
100 hours  
1. Check Engine Oil Level  
2. Inspect for damage  
X
3. Wipe off outside with clean,  
slightly moist cloth  
1. Change Engine Oil  
2. Clean Air Filter (69)  
X
X
X
X
X
(Replace Filter as needed)  
Clean Deposit Cup (76)  
(Clean monthly in dusty areas)  
X
X
X
X
Clean Spark Plug (44)  
(Replace as needed)  
Engine Overhaul  
refer to  
a
small engine service  
manual for procedures. service is  
to be performed only by a qualied  
mechanic and includes:  
X
1. Valve Clearance Check/Adjust  
2. Clean Combustion Chamber  
3. Clean Fuel Tank, Filter, and Supply  
Line(replacelterandlineasneeded)  
troublesHootinG  
problem  
Engine will not start  
possible causes  
1. Fuel Tank empty.  
probable solutions  
1. Check fuel level at Fuel Meter (1a).  
2. Put Valves (9a, 81) in ON position.  
3. Move Choke Control left to start.  
4. Turn switch to ON position.  
2. Fuel Valve(s) closed.  
3. Choke not in proper start position.  
4. ON/OFF Switch off.  
5. Oil level low.  
5. Check engine oil level.  
6. Spark Plug damaged, gapped incorrectly, or 6. Check Spark Plug gap, condition, and  
connected improperly.  
connection.  
7. Mechanical/electrical problem.  
7. Have qualified mechanic inspect and repair.  
Engine is running, but  
power is not being supplied  
to outlets.  
1. Circuit Protection (59a, 53a) tripped. Pilot  
Light (56a) will be off.  
1. Reduce electrical load and reset Circuit  
Protection (53a).  
2. Electrical problem.  
2. Have a qualified technician service unit.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 14  
 
parts list - enGine  
part  
description  
Crankcase  
qty  
1
1
2
2
1
1
1
1
1
1
1
1
1
2
4
1
1
1
1
2
1
2
1
2
2
1
1
1
1
1
1
6
1
2
2
1
1
1
2
2
2
part  
description  
qty  
1
1
1
6
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
3
3
1
1
1
1
1
2
4
4
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
42 Gasket, cylinder head  
43 Cylinder cover  
44 Spark plug  
Valve chamber clapboard sub-assy  
Stud M5 × 118  
Stud M6 × 52  
45 Bolt M6 × 35  
Oil seal (17×30×6), crankshaft  
Cover, oil filter  
46 Gasket, intake port  
47 Carburetor assy.  
48 Connecting block  
49 Gasket, carburetor  
50 Governor arm  
51 Pull-rod, governor  
52 Lock bolt  
Gasket  
Return pipe  
Flow guard, lower  
10 Sway bar  
11 Keeper, sway bar  
12 Oil seal, sway bar  
13 Washer, sway bar  
14 Bolt M6 × 14  
53 Return spring  
54 Assistant spring, governor  
55 Mount, governor  
56 Nut M6  
15 Bolt M5 × 10  
16 Crankshaft sub-assy  
17 Connecting rod  
18 Piston  
57 Ignition coil/Spark plug wire assy.  
58 Bolt M6 × 27  
59 Fan, flywheel  
19 Piston pin  
60 Starting flange  
61 Flywheel  
20 Circlip, piston pin  
21 Piston ring set  
22 Set pin Ø8 × 14  
23 Gasket, crankcase  
24 Drain plug  
62 Nut M12 × 1.25  
63 Fan hood sub-assy  
64 Recoil starter  
65 Bolt M6 × 8  
25 Washer  
66 Bolt M6 × 14  
26 Crankcase cover  
27 Oil seal (17×30×6), crankshaft  
28 Dipstick sub-assy  
29 Oil plug sub-assy  
30 Driven gear sub-assy, governor  
31 Bearing 6203  
32 Bolt M6 × 29  
67 Cover, air filter  
68 Housing, air filter  
69 Foam, air filter  
70 Bracket, air filter  
71 Gasket, air filter  
72 Nut M6  
73 Pan screw M6 × 10  
74 Washer 5  
33 Camshaft  
34 Washer, camshaft  
35 Tappet  
75* O-ring  
76* Deposit Cup  
36 Intake valve  
77* Carburetor Drain Plug  
78 Spark Plug Socket  
79 Socket Handle  
80* Choke Control  
81* Fuel Valve  
37 Exhaust valve  
38 Oil seal, valve stem  
39 Spring seat, valve  
40 Valve spring  
*Part of Carburetor assy. (47)  
41 Cap  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 15  
 
asseMbly diaGraM - enGine  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 16  
 
parts list a - Generator  
part  
1a  
description  
Fuel Meter  
qty  
1
part  
31a Gasket  
description  
qty  
1
2a  
Fuel Tank Cap  
Fuel Tank Filter  
Flange Bolt M6 x 20  
Gasket  
1
32a Spring Gasket  
33a Bolt M8 x 170  
34a Magneto Cover  
35a Gasket  
1
3a  
1
1
4a  
4
1
5a  
4
2
6a  
Screw Gasket  
Anti-vibration Gasket  
Fuel Tank  
4
36a Spring Gasket  
37a Bolt M5 x 8  
38a Lock Nut M8  
39a Gasket  
2
7a  
4
2
8a  
1
6
9a  
Fuel Valve  
1
8
10a Fuel Pipe Clamp  
11a Oil Pipe  
2
40a Spring Gasket  
41a Bolt M8 x 40  
42a Cushion  
8
1
8
12a Engine (See parts list on earlier page)  
13a Exhaust Pipe Gasket  
14a Exhaust Pipe  
15a Lock Nut M8  
16a Flange Bolt M6 x 12  
17a Muffler Gasket B  
18a Muffler  
1
2
1
43a Frame  
1
1
44a Anti-vibration Feet  
45a Flex Tube  
4
2
1
2
46a Circuit Cover  
47a Bolt M4 x 10  
48a Capacitor  
1
1
2
1
1
19a Flange Bolt M6 x 12  
20a Front Cover  
1
49a Bolt M4 x 16  
50a Panel  
1
1
1
21a Gasket  
4
51a Bolt M6 x 25  
52a Engine Switch  
53a AC Circuit Protector  
54a AC Outlet  
4
22a Flange Bolt M8 x 20  
23a Rotor Assembly  
24a Stator Assembly  
25a Wiring Cover  
26a Rear Cover  
4
1
1
1
1
2
1
55a Grounding Point  
56a Pilot Lamp  
1
1
1
27a Rectifier  
1
57a Battery Charging Socket  
58a Voltmeter  
1
28a Gasket  
4
1
29a Spring Gasket  
30a Bolt  
4
59a DC Circuit Protector  
60a Battery Charging Cord  
1
4
1
please read tHe followinG carefully  
tHe Manufacturer and/or distributor Has proVidedtHe parts list and asseMbly  
diaGraM intHis Manual as a referencetool only. neitHertHe Manufacturer or  
distributor Makes any representation orwarranty of any kindtotHe buyertHat  
He or sHe is qualified to Make any repairs to tHe product, or tHat He or sHe is  
qualifiedto replace any parts oftHe product. in fact,tHe Manufacturer and/or  
distributor eXpressly statestHat all repairs and parts replaceMents sHould  
be undertaken by certified and licensedtecHnicians, and not bytHe buyer. tHe  
buyer assuMes all risk and liability arisinG out of His or Her repairs to tHe  
oriGinal product or replaceMent parts tHereto, or arisinG out of His or Her  
installation of replaceMent parts tHereto.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 17  
 
asseMbly diaGraM a - Generator  
record products serial number Here:  
note: If product has no serial number, record month and year of purchase instead.  
note: Some parts are listed and shown for illustration purposes only, and are not available  
individually as replacement parts.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 18  
 
Harbor freight tools emission  
control defects warranty  
provisions  
eMission control  
systeM warranty  
california and united states  
emission control defects  
1.  
2.  
length of coverage  
HFT warrants to a first retail purchaser and each subsequent  
purchaser that the engine is free from defects in materials  
and workmanship that cause the failure of warranted parts  
for a period of two (2) years after the date of delivery to the  
first retail purchaser.  
warranty statement  
The California Air Resources Board (herein CARB), the United  
States Environmental Protection Agency (herein EPA), and Harbor  
®
Freight Tools (herein HFT) are pleased to explain the emission  
control system warranty on your 1995 and later Small Off-Road  
Engine (herein engine). In California, the engine must be de-  
signed, built and equipped to meet the State’s stringent anti-smog  
standards. Elsewhere within the United States, new off-road,  
spark-ignition engines certified for model year 1997 and later, must  
meet similar standards set forth by the EPA. HFT must warrant  
the emission control system on your engine for the periods of time  
described below, provided there has been no abuse, neglect or  
improper maintenance of your engine.  
no charge repair or replacement  
Repair or replacement of any warranted part will be performed  
at no charge to the owner if the work is performed through a  
warranty station authorized by HFT. For emissions warranty  
service, contact the HFT Customer Service Department at  
1-800-444-3353.  
3.  
4.  
consequential damages coverage  
Coverage under this warranty shall also extend to the failure of  
any engine components caused by the failure of any warranted  
part while it is still covered under this warranty.  
Your emission control system may include parts such as the  
carburetor or fuel-injection system, and the ignition system. Also  
included may be hoses, belts, connectors and other emission-  
related assemblies.  
Where a warrantable condition exists, HFT will repair your engine  
at no cost to you including diagnosis, parts and labor.  
coverage exclusions  
Warranty claims shall be filed in accordance with the provi-  
sions of the HFT warranty policy explained in the box at the  
top of the previous page. HFT shall not be liable for any loss  
of use of the engine, for any alternative usage, for any damage  
to goods, loss of time, or inconvenience. Warranty coverage  
shall also be excluded for any part which fails, malfunctions,  
or is damaged due to failure to follow the maintenance and  
operating instructions set forth in the Owner’s Manual includ-  
ing, but not limited to:  
Manufacturers warranty coverage  
The 1995 and later engines are warranted for two (2) years. If any  
emission-related part on your engine is defective, the part will be  
repaired or replaced by HFT.  
Harbor freight tools emission  
control defects warranty  
(a) use of parts which are not authorized by HFT  
(b) improper installation, adjustment or repair of the engine  
or of any warranted part unless performed by an autho-  
rized warranty center  
coverage  
Engines are warranted for a period of two (2) years relative to  
emission control parts defects, subject to the provisions set forth  
below. If any emission related part on your engine is defective, the  
part will be repaired or replaced by HFT.  
(c) failure to follow recommendations on fuel use contained  
in the Owner’s Manual  
(d) improper or inadequate maintenance of any warranted  
parts  
owners warranty responsibilities  
(e) repairs performed outside of the authorized warranty  
service dealers  
-
As the engine owner, you are responsible for the performance  
of the required maintenance listed in your Owner’s Manual.  
HFT recommends that you retain all receipts covering main-  
tenance on your engine, but HFT cannot deny warranty  
solely for the lack of receipts or for your failure to ensure the  
performance of all scheduled maintenance.  
(f) alterations by changing, adding to or removing parts from  
the engine.  
5.  
service and Maintenance  
-
-
As the engine owner, you should, however, be aware that  
HFT may deny you warranty coverage if your engine or a part  
has failed due to abuse, neglect, improper maintenance, or  
unapproved modifications.  
Component parts which are not scheduled for replacement  
as required maintenance or are scheduled only for regular  
inspection to the effect of “repair or replace as necessary”  
are warranted for the warranty period. Any warranted part  
which is scheduled for replacement as required maintenance  
is warranted for the period of time up to the first scheduled  
replacement point for that part. Any replacement part, pro-  
vided it is equivalent in durability and performance, may be  
used in performance of maintenance or repairs. The owner  
is responsible for commissioning a qualified technician/me-  
chanic to perform all required maintenance, as outlined in  
the Maintenance and cleaning sections on page 13-14 of  
this manual.  
You are responsible for shipping your engine to a HFT war-  
ranty station as soon as a problem exists. Contact the HFT  
Customer Service department at the number below to make  
shipping arrangements. The warranty repairs should be  
completed in a reasonable amount of time, not to exceed 30  
days.  
If you have any questions regarding your warranty rights and re-  
sponsibilities, you should contact the Harbor FreightTools Customer  
Service Department at 1-800-444-3353.  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 19  
 
4) catalyst system (if so equipped)  
i) Exhaust pipe stud.  
6.  
warranted parts  
1) fuel Metering system  
ii) Muffler.  
iii) Catalytic converter (if so equipped).  
i)  
Carburetor and its internal parts.  
ii) Fuel pump (if so equipped).  
iii) Cold start enrichment system.  
5) Miscellaneous items used in above systems  
i)  
Vacuum, temperature and time sensitive valves and  
switches.  
2) air induction system  
i)  
Intake pipe/manifold.  
ii) Hoses, belts, connectors, and assemblies.  
ii) Air cleaner.  
3) ignition system  
i)  
Spark plug.  
ii) Magneto ignition system.  
warranty  
lIMIteD 1yeAR  
WARRANty  
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and durability standards,  
and warrants to the original purchaser that this product is free from defects in materials and workmanship  
for the period of one year from the date of purchase (90 days if used by a professional contractor or if used  
as rental equipment). This warranty does not apply to damage due directly or indirectly, to misuse, abuse,  
negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance. We shall in no  
event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential  
damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental  
or consequential damages, so the above limitation of exclusion may not apply to you. THiS WarranTy iS  
expreSSly in lieu oF all oTHerWarranTieS, expreSS or implied, inCludingTHeWarranTieS  
oF merCHanTabiliTy and FiTneSS.  
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.  
proof of purchase date and an explanation of the complaint must accompany the merchandise. if our inspection  
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase  
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our  
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of  
our warranty, then you must bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 94678  
for technical questions, please call 1-800-444-3353.  
Page 20  
 

Belkin Network Card P75481 User Manual
Black Box Switch KV9612A User Manual
Blue Rhino Charcoal Grill CBC911W User Manual
Bosch Power Tools Impact Driver 1194AVSR User Manual
Boss Audio Systems Speaker CX104DVC User Manual
Bradford White Corp Water Heater LD 12UT3 1 User Manual
Brother Sewing Machine INNOVIS 500 User Manual
Califone Headphones 2810 BE User Manual
Cambridge SoundWorks CD Player C174RCNB User Manual
Cannon Fishing Equipment 10 User Manual