CDA543F
BEKO plc
Beko House
Caxton Way
Watford
Hertfordshire
WD18 8UF
Tel: 01923 654650
Fax: 01923 819653
e-mail: [email protected]
Printed in Turkey
Part no: 48 2711 00 00
Revision no: 0
ELECTRICAL REQUIREMENTS
TRANSPORTATION INSTRUCTIONS
Before you insert the plug into the wall socket make sure that the voltage and the
frequency shown in the rating plate inside the appliance corresponds to your
electricity supply.
1. The appliance should be transported only in a vertical upright position. The
packing as supplied must be intact during transportation.
2. If during the course of transport the appliance has to be transported
horizontally, it must only be laid on its right hand side when standing in the
front of the appliance. After bringing it to upright position,it must not be operated
for at least 4 hours to allow the system to settle.
Rating label is on the left hand side of fridge inner liner.
We recommend that this appliance is connected to the mains supply via a
suitable switched and fused socket in a readily accessible position.
Should the mains lead of the appliance become damaged or should it need
replacing at any time, it must be replaced by a special purpose made mains lead
which can only be obtained from a BEKO Authorised Service Agent.
3. Failure to comply with the above instructions could result in damage occuring
to the appliance. The manufacturer will not be held responsible if these
instructions are disregarded.
4. The appliance must be protected against rain, moisture and other
atmospheric influences.
WARNING! THIS APPLIANCE MUST BE EARTHED
If the fitted moulded plug is not suitable for your socket, then the plug should be
cut off and an appropriate plug fitted. Destroy the old plug which is cut off as a
plug with bared cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
5. When positioning your appliance take care not to damage your flooring,
pipes, wall coverings etc. Do not move the appliance by pulling by the door
or handle.
6. Empty any water in the drain tray before moving. See section ‘Defrosting’ and
‘Care & cleaning’ for further information.
The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse
need to be replaced an ASTA approved BS 1362 fuse of the same rating must be
used. Do not forget to refit the fuse cover. In the event of losing the fuse cover the
plug must not be used until a replacement fuse cover has been fitted. Colour of
the replacement fuse cover must be the same colour as that visible on the pin face
of the plug. Fuse covers are available from any good electrical store.
7. Make sure that the defrost water pipe at the back of the product is fixed to the
plastic evaporating pan on the top of the compressor, to avoid defrost water
spillage on the floor.
IMPORTANT : Care must be taken while cleaning / carrying the appliance to
avoid touching the bottom of the condenser metal wires at the back of the
appliance as you might injure your fingers and hands.
IMPORTANT! FITTING A DIFFERENT PLUG
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals
in your plug proceed as follows:
Do not attempt to sit or stand on top of your appliance as it is not designed for
such use. You could injure yourself or damage the appliance.
"IMPORTANT: Make sure that mains cable is not caught under the appliance
during and after carrying / moving the appliance, to avoid the mains cable
becoming cut or damaged."
(See diagram).
6mm.
GREEN &
YELLOW
OR
1. Connect the green-yellow or
GREEN
green (Earth) wire to the terminal
in the plug marked 'E' or with
L
Do not allow children to play with the appliance or tamper with the controls.
BROWN
OR
BEKO plc declines to accept any liability should the instructions not be
followed.
N
RED
the symbol
or coloured
22mm.
IMPORTANT
BLUE
OR
green and yellow or green.
INSTALLATION INSTRUCTIONS
BLACK
1. The space in the room where the appliance is installed must not be smaller
than 10 cubic metres.
2. Connect the blue (Neutral) wire
to the terminal in the plug
2. Do not put your fridge freezer in a cold room where the temperature is likely
to go below +5 degrees C (41 degrees F) during night time and/or especially
in winter.
CORD GRIP
marked 'N' or coloured black.
3. Connect the brown (Live) wire to
the terminal in the plug marked 'L'
or coloured red.
This fridge freezer has been designed to operate in ambient temperatures
between +5 and +32 degrees C (41 and 90 degrees F) Therefore if the
appliance is installed in an unheated/cold room (eg: conservatory/annex/
shed/garage etc) then the appliance will not operate causing the freezer
compartment to run warmer and as a result the storage time of frozen food
With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or
in the main fuse box.
If in doubt contact a qualified electrician.
3
4
may be reduced.
GETTING TO KNOW YOUR COMBI BEKO FRIDGE / FREEZER
3. Do not place the appliance near cookers, radiators or in direct sunlight as this
will cause your appliance to work harder. If installed next to a source of heat
or freezer, maintain the following minimum side clearances:
From Cookers
From Radiators
From Freezers
50 mm (2")
300 mm (12")
25 mm (1")
EGG TRAY
THERMOSTAT KNOB
INTERIOR LIGHT
CABINET SHELVES
4. Make sure that sufficient room is provided
around the appliance to ensure free air
circulation.
DEFROST WATER
COLLECTION CHANNEL
SALAD
CRISPER
Fit the Two plastic wall spacers
supplied with the appliance rotating
1/4 turn to the condenser at the back
of the appliance (See Diagram).
INTERIOR
LIGHT BUTTON
ICE BANK
FREEZER FAN
5. The fridge/freezer should be located on a
smooth surface. The two front feet
can be adjusted as required. To ensure
that your appliance is standing
FAST FREEZE
COMPARTMENT
upright adjust the two front feet by turning
clockwise or anti-clockwise, until
the product is in firm contact with the floor.
Correct adjustment of feet avoids
excessive vibration and noise.
FROZEN FOOD
STORAGE DRAWERS
6. Refer to cleaning and care section to prepare your appliance for use.
A special receptacle is supplied to store the mains plug during transit.
The receptacle is fixed at the back of the
cabinet, on the side of the compressor.
(See diagram) Gently remove the plug
from the receptacle. Never pull the
mains cord, you may damage the
ADJUSTABLE
FEET
appliance. In the case of transportation,
ensure you locate the plug in the receptacle
provided to avoid transit damage.
5
6
REVERSING THE DOORS
(item 7)
(item 10)
(item 15)
We recommend that you reverse doors before switching on for the first time.
Tools required: Small and medium size flat and cross-headed screwdrivers, a pair of pliers.
Spare Parts supplied in the plastic bag: The following parts, which are exclusively for left hand side fitted hinge operation
are supplied in a plastic bag with the appliance:
- Upper door top trim hinge cover.
20
- Upper door middle hinge bushing/door stopper assembly.
- Hinge pin bushings, 2 different parts supplied as spares for future use.
- Hinge pin hole blanking plug, 1 piece supplied as spare for future use.
1
3
7
1
We suggest you keep all the parts supplied in the plastic bag and also parts, which have been removed when reversing
doors, in a safe place for possible future, re-use.
IMPORTANT: We suggest you ask somebody to help you when moving the appliance around and to hold doors when
6
removing / re-fitting hinges and doors to avoid any injury and damage to the product.
Please refer to diagrams supplied. To follow numbers in brackets below, refer to the main diagram.
2
5
1. Switch off the appliance at the socket outlet and pull out the mains plug.
2. Remove all loose items and fittings and food, if any, from inside the appliance and door racks.
3. Gently prise off plastic hinge cover of upper door top trim and hinge covers on both sides of front top panel using a
small flat-headed screwdriver. (1)
11
14
4. Gently tilt the appliance back against a strong wall on its rear side sufficiently to allow the lower hinge to be
removed. Take care to protect the appliance, your wall and floor coverings. You can utilise the original
packaging to do this. Once you tilt the appliance back, check to make sure the appliance is completely
stable and safe before you carry on. (2)
13
45 °
9
5. Unscrew and remove the lower hinge using a cross-headed screwdriver while holding the lower door
firmly.(3)
4
6. Remove lower door carefully off the middle hinge and stand door upright in a safe place.(4)
7. Open upper door and unscrew and remove the middle hinge while holding the upper door firmly. Use a
flat-headed screwdriver. Middle hinge will need to be rotated 180 degrees before re-fitting on the opposite
side.(5)
3
10
8. Remove upper door carefully off the upper hinge and stand door upright in a safe place.(6)
9. Unscrew and remove the upper hinge using a flat-headed screwdriver.(7)
10. Rotate the upper hinge 180 degrees and then unscrew and remove the hinge pin using a pair of pliers and re-fit to
opposite side of hinge.(8)
11. Reposition plugs and hinge pin bushings on top of doors on the opposite side of both doors. Use small flat-
headed screwdrivers to remove plugs and bushings. Take care not to mark doors.(9)
12. Reposition left hand side feet on the opposite side.(10)
11
13. Unscrew and remove the bottom door hinge pin bushing/door stopper using a cross-headed
screwdriver. (11)
20
20
Unscrew and remove the upper door middle hinge pin bushing/door stopper using a cross-headed
screwdriver. Important: This part cannot be used on the opposite side; left hand side middle hinge pin
bushing/door stopper part is supplied in the plastic bag.(11)
12
180°
8
15
14. Re-fit the upper hinge on the left hand side using flat-headed screwdriver.(12)
15. Fit upper door left hand side middle hinge pin bushing/door stopper supplied in the plastic bag using
cross-headed screwdriver.(13)
16. Reposition three small plastic plugs on the left hand side, which are covering middle hinge holes, on the
opposite side to cover holes left empty.(14)
17. Locate and re-fit upper door to upper hinge and hold the door firmly.(15)
18. Locate the middle hinge pin to middle hinge pin bushing of upper door on the left hand side and re-fit the
middle hinge.(16) First fit the left screw when the door is closed and then fit the right screw after opening the door
for access.
16
19. Reposition the screw fitted to lower hinge hole on the left hand side at the bottom of the cabinet on
the opposite side.(17)
18
20. Locate and re-fit lower door to middle hinge pin and then re-fit the lower hinge on the left hand side.(18),(19)
21. Carefully stand the appliance upright and adjust the two front feet if necessary.
22. Check that doors open and close easily, they are aligned correctly and that there are no gaps allowing
air into the cabinet. If there are gaps between the door seal and the cabinet, adjust the door seal by gently
pulling away from the door using fingers.
23. Check that all the hinge screws are tightened. Avoid over tightening the screws.
24. Put all items, fittings back in the appliance.
25. Fit upper door top trim and front top panel plastic hinge covers. Upper door top trim hinge covers are
supplied in the plastic bag.(20)
17
26. Wait for at least 4 hours to allow the system to settle before switching on.
19
27. Once the correct storage temperatures have been r7eached in the appliance, put back all the food.
8
TEMPERATURE CONTROL AND ADJUSTMENT
SUGGESTED ARRANGEMENT OF FOOD IN THE FRIDGE/FREEZER
Arrangement Examples (See diagram)
7
8
1
1. Baked, chilled cooked food,
dairy products, cans.
9
2
2. Meat, sausages, cold cuts.
3. Fruit, vegetables, salads.
10
3
4
4. Making, storing ice cubes.
5. Frozen food.
6. Frozen food and
6
freezing of fresh food.
7. Butter, cheese.
8. Small bottles, cans, tubes.
Operating temperatures are controlled by the thermostat knob (see diagram) located
on the ceiling of fridge compartment. Settings may be made from 1 to 5, 5 being
the coldest position.
5
9. Eggs.
10. Tall, large bottles, beverages.
When the appliance is switched on for the first time, the thermostat should be
adjusted so that after 24 hours, the average fridge temperature is no higher than
+5°C (+41°F). We recommend you set the thermostat half way between the 1 and
5 setting and monitor to obtain the desired temperature i. e. towards 5 you will
obtain a colder fridge temperature and vice versa. Some sections of the fridge may
be cooler or warmer ( such as the salad crisper and the top part of the cabinet )
which is quite normal.
The following guidelines and recommendations are suggested to obtain the best
results and storage hygiene.
1. The fridge compartment is for the short term storage of fresh food and drinks.
2. The freezer compartment is
rated and suitable for the freezing and
storage of pre frozen food. The recommendation for
storage as
stated on the food packaging should be observed at all times.
3. Cooked dishes must be stored in airtight covered containers.
4. Fresh wrapped produce can be placed on the shelf. Fresh fruit and
vegetables should be cleaned and stored in the crisper bins.
5. Bottles can be placed in the door section.
The normal storage temperature of the freezer should be -18°C (0°F). Lower
temperatures may be obtained by adjusting thermostat knob towards 5 position.
We recommend that you check the temperature with an accurate thermometer to
ensure that the storage compartments are kept to the desired temperature.
Remember you must take your reading very quickly since the thermometer
temperature will rise very rapidly after you remove it from the freezer.
Please remember each time the door is opened cold air escapes and the internal
temperature rises. Therefore never leave the door open and ensure it is closed
immediately after food is put in or removed.
6. To store raw meat, wrap in polythene bags and place on the lowest shelf. Do
not allow to come into contact with cooked food to avoid contamination. For
safety, only store raw meat for two to three days.
7. Keep the food packed wrapped or covered. Allow hot food and beverages to
cool before placing them in the fridge. Do not store explosive substances. High
proof alcohol must be stored upright in sealed containers. Left over canned
food should not be stored in the can.
8. Fizzy drinks should not be frozen and products such as flavoured water ices
should not be consumed too cold.
In case of a temporary ice build up in the fridge compartment, reduce the
thermostat setting to 1, monitoring at the same time that the fridge temperature
is maximum +5 degrees C [41 degrees F]. Once the ice build up disappears
and the appliance starts auto defrosting again as normal, then you may
increase the thermostat setting, if required.
9. Some fruit and vegetables suffer damage if kept at temperatures near 0°C.
Therefore wrap pineapples, melons, cucumbers, tomatoes and similar produce
in polythene bags.
10. Place chilled cooked food and similar food near the rear of the fridge inner
liner where the cold wall is located.
When you set the thermostat knob to 0 [Zero] position, the appliance will be switched
off.
11. Shelves, racks, crisper bins, drawers, flaps, bottle grippers are all removable.
12. Do not leave frozen food at room temperature to thaw; the best way to defrost
food is to put it in the fridge to thaw slowly. Make sure you avoid defrosting
food or food juices drip onto other food.
13. For hygiene reasons, always wrap food using a suitable packaging material
before storing in your appliance to avoid contact with the appliance surface.
9
10
STARTING
FREEZING FRESH FOOD
Final Check
Please observe the following instructions to obtain the best results.
Before you start using the fridge/freezer check that:
Do not freeze too large a quantity at any one time. The quality of the food is best
preserved when it is frozen right through to the core as quickly as possible.
Do not exceed the freezing capacity of your appliance in 24 h which is 4 kg (8.8 lb)
1. The feet have been adjusted for perfect levelling.
2. The interior is dry and air can circulate freely at the rear of the cabinet.
3. Clean the interior as recommended under "CLEANING AND CARE."
4. Insert the plug into the wall socket and switch on the electricity supply.
• When the door is open the fridge interior light will come on.
Placing warm food into the freezer compartment causes the refrigeration compressor to
operate continuously until the food is frozen solid. This can temporarily lead to excessive
cooling of the refrigeration compartment.
5. You will hear a noise as the compressor starts up. The liquid and gases sealed
within the refrigeration system may also give rise to noise, whether the
compressor is running or not which is quite normal.
When freezing fresh food turn the thermostat knob towards 5 Small quantities
of food up to 1/2 kg. (1 lb) can be frozen without having to rotate the temperature
control knob.
“Due to operation of the fan inside the frost free freezer compartment, overall noise
level is slightly higher in comparison to non-frost free appliances. This is quite normal
and is not a fault.”
6. Set the thermostat knob half way between 1 and 5.
You may place fresh food to be frozen in any part of the freezer.
7. Front edges of the cabinet may feel warm. This is normal. These areas are designed to
be warm to avoid condensation.
Take special care not to mix already frozen food and fresh food.
8. "Do not load the appliance immediately it is switched on. Wait until the correct storage
temperature has been reached. We recommend that you check the temperature with
an accurate thermometer (see; Temperature Control and Adjustment)"
9. When the freezer reaches the desired temperature the freezer fan will stop. When the
freezer fan is on, the noise will be louder when the freezer door is opened.
10. Avoid spillage of food particularly small items like rice, peas, beans through the fan
guard as they may cause the cooling system to block and therefore operate less efficiently.
MAKING ICE CUBES
Fill the ice - cube tray 3/4 full with water and place it in the Ice Bank. Loosen
frozen trays with the handle of a spoon, never use sharp edged objects
such as knives, forks. Store ice-cubes in the Ice Bank.
Note: If freshly made ice cubes are not consumed for several weeks and stored
in Ice Bank, they will slowly reduce in size and eventually disappear completely.
STORING FROZEN FOOD
Prepacked commercially frozen food should be stored in accordance with the
frozen food manufacturer's instructions for a
compartment.
frozen food storage
To ensure that the high quality achieved by the frozen food manufacturer and the
food retailer is maintained, the following should be remembered:
1. Put packets in the freezer as quickly as possible after purchase.
2. Ensure that contents are labelled and dated.
3. Do not exceed "Use By", "Best Before" dates on the packaging.
If there is a power failure do not open the door. Frozen food should not be
affected if the failure lasts for less than 13 hrs. If the failure is longer, then the
food should be checked and either eaten immediately or cooked and then re-
frozen.
12
11
CLEANING AND CARE
DEFROSTING
** We recommend that you switch off the appliance at the socket outlet and pull
out the mains plug before cleaning.
A) FRIDGE COMPARTMENT
** Never use any sharp abrasive instrument, soap, household cleaner, detergent
and wax polish for cleaning.
The fridge compartment defrosts
(2)
automatically. The defrosting water runs
to the drain tube via a collection
container at the back of the appliance (1).
(see diagram)
During defrosting water droplets may form
at the back of the fridge compartment
where concealed evaporator is located.
Some droplets may remain on the liner and
refreeze when defrosting is completed. Do
not use pointed or sharp edged objects such as knives, forks to remove the droplets
which have frozen.
If at any time the defrost water does not drain from the collection channel, check
to ensure that no food particles have blocked the drain tube. The drain tube can
be cleared by pushing the special plastic plunger provided down the drain tube
(2). If the frost layer reaches about 1/4"(7 mm), reduce the setting (i.e. from 4 to
1) to restart automatic defrosting.
Defrost
Water
** Use luke warm water to clean the cabinet of the appliance and wipe it dry.
** Use a damp cloth wrung out in a solution of one teaspoon of bicarbonate of
soda to one pint of water to clean the interior and wipe it dry.
** Make sure that no water enters the lamp housing.
** If the appliance is not going to be used for a long period of time switch it off,
remove all food, clean it and leave the door ajar.
** We recommend that you polish the metal parts of the product (i.e. door
exterior, cabinet sides) with a silicone wax (car polish) to protect the high
quality paint finish.
Drain Tube
Collection
(1)
** Any dust that gathers on the condenser, which is located at the back of the
appliance, should be removed once a year with a vacuum cleaner.
** Check door seals regularly to ensure they are clean and free from food
particles.
** Removal of door tray
• To remove door racks, remove all the contents and then simply push the
door rack upwards from the base.
** To remove a freezer drawer, pull it as far as possible, and then tilt it upwards,
and then pull it out completely.
B) FREEZER COMPARTMENT
** To remove the freezer flap door, first open the door 3” and then gently pull it
off. Make sure that the flap is in place before closing the freezer door.
The freezer compartment defrosts automatically.
** Avoid spillage of food particularly small items like rice, peas, beans through the
fan guard as they may cause the cooling system to block and therefore operate
less efficiently.
STAINLESS STEEL DOOR CLEANING INSTRUCTIONS [ONLY VALID FOR
STAINLESS STEEL MODELS WHICH HAVE “X” SUFFIX IN THE MODEL NUMBER]
Warnings!
The fan inside the freezer compartment circulates cold air. Never insert
any object through the guard. Do not allow children to play with
the freezer fan.
Never store products that contain inflammable propellant gas
(eg dispensers, spray cans etc.) or explosive substances.
Don’t cover the shelves with any protective materials, which may obstruct
air circulation.
Do not allow children to play with the appliance or tamper with the controls.
Do not obstruct the freezer fan guard to ensure that you
obtain the best possible performance from your appliance.
Stainless steel surfaces of your appliance require special cleaning methods. In
order to eliminate marks on doors and to keep your appliance doors clean,
we recommend you the following to clean and wipe the stainless steel surfaces
of doors:
1. You can purchase special cleaning materials suitable for stainless steel
surfaces of kitchen appliances from your local store. Follow the instructions
supplied by the manufacturer of such cleaning materials.
2. You can purchase a special micro-fibre cleaning cloth pack called “E-cloth”
from your local electrical or hardware store, which is suitable to clean and
wipe stainless steel surfaces of kitchen appliances without the need to use any
chemicals or other cleaning materials. You just need warm water. You need to
follow the instructions supplied inside the packaging of E-cloth.
Freezer fan
13
14
DO'S AND DON'TS
Never attempt to clean, wipe or treat the stainless steel and other surfaces of
your appliance with unsuitable material, do not clean or wipe handles and
plastic surfaces using stainless steel cleaning materials, otherwise, your guarantee
will be void.
Do- Clean your appliance regularly (See "Cleaning and Care")
Do- Keep raw meat and poultry below cooked food and dairy products.
Do- Take off any unusable leaves on vegetables and wipe off any soil.
Do- Leave lettuce, cabbage, parsley and cauliflower on the stem.
Do- Wrap cheese firstly in greaseproof paper and then in a polythene bag
excluding as much air as possible. For best results take out of the fridge
compartment an hour before eating.
REPLACING THE INTERIOR LIGHT BULB (See diagram)
Do- Wrap raw meat and poultry loosely in polythene or aluminium foil. This
prevents drying.
Should the light fail to work, proceed as follows.
1. Switch off at the socket outlet and pull out the mains plug.
• You may find it useful to remove shelves for easy access.
Do- Wrap fish and offal in polythene bags.
Do- Wrap food which have a strong odour or can dry out in polythene bags,
aluminium foil or place in an airtight container.
Do- Wrap bread well to keep it fresh.
2. Use a flat tipped screwdriver to remove the light diffuser cover by inserting the
blade in each of the two recesses to prise off each side.
Do- Chill white wines, beer, lager and mineral water before serving.
Do- Check contents of the freezer every so often.
Do- Keep food for as short a time as possible and adhere to "Best Before",
"Use by" etc. dates.
Do- Store commercially frozen food in accordance with the instructions given
on the packets that you buy.
3. First check that the bulb hasn’t worked loose by ensuring it is screwed securely
in the holder. Replace the plug and switch on. If the bulb works, replace the light
cover by inserting the rear lug and pushing up to locate the front two lugs.
Do- Always choose high quality fresh food and be sure it is thoroughly clean
before you freeze it.
Do- Prepare fresh food for freezing in small portions to ensure rapid freezing.
Do- Wrap all food in aluminium foil or freezer quality polythene bags and
make sure any air is excluded.
4. If the light still fails to work, switch off at the socket outlet and pull out the mains
plug. Replace the bulb with a new 15 watt (max) screw cap (SES) bulb.
Do- Wrap frozen food when you buy it and put it in to the freezer as soon as
possible.
Do- Defrost food in the fridge compartment.
5. Carefully dispose of the burnt-out light bulb immediately.
Replacement light bulb can easily be obtained from a good local electrical or DIY
store.
Do- Remove ice cream from the freezer 10-20 minutes before serving.
Don't- Store bananas in your fridge compartment.
Don't- Store melon in your fridge. It can be chilled for short periods as long as it
is wrapped to avoid it flavouring other food.
Don't- Cover the shelves with any protective materials which may obstruct air
circulation through them.
Don't- Store poisonous or any dangerous substances in your appliance.
It has been designed for the storage of edible foodstuffs only.
Don't- Consume food which has been stored for an excessive time in the fridge.
Don't- Store cooked and fresh food together in the same container. They should
be packaged and stored seperately.
Don't- Let defrosting food or food juices drip onto food.
Don't- Leave the door open for long periods as this will make the appliance more
costly to run and cause excessive ice formation.
Don't- Use pointed sharp edged objects such as knives, forks to remove the ice.
Don't- Put hot food into the appliance. Let it cool down first.
Don't- Put liquid-filled bottles or sealed cans containing carbonated liquids into
the freezer as they may burst.
Don't- Exceed the maximum freezing loads (4 kg in any 24 hours) when
freezing fresh food.
Don't- Give children ice-cream and water ices direct from the freezer. The low
temperature may cause 'freezer burns' on lips.
Don't- Freeze fizzy drinks.
Don't- Try to keep frozen food which has thawed, it should be eaten within
24 hours or cooked and refrozen.
Don't- Remove items from the freezer with wet hands.
Don't- Close the freezer door before placing the compartment cover in its place.
Don’t- Leave frozen food at room temperature to thaw; the best way to defrost
food is to put it in the fridge to thaw slowly. Make sure you avoid defrosting
food or food juices drip onto other food.
15
16
ENERGY SAVING TIPS
GUARANTEE DETAILS
1- Ensure your appliance is installed in a well ventilated area. If the ambient
temperature is low (but in no case lower than 5 degrees C), then the energy
saving will be more. In this case, check temperatures of fridge and freezer
compartments with an accurate thermometer and lower the thermostat setting
(towards 1) if necessary.
Your new Beko product is guaranteed against the cost of breakdown repairs for
twelve months from the date of the original purchase.
What is covered?
• Repairs necessary as a result of faulty materials, defective components or
manufacturing defect.
2- Ensure the time between buying chilled/frozen food and placing them in your
appliance is kept at minimum, particularly in summer. We recommend you use
a cool bag or a special carrier bag to carry frozen food.
• The cost of functional replacement parts, but excluding consumable items.
• The labour costs of a Beko approved repairer to carry out the repair.
3- Do not leave the door (s) of your appliance open longer than necessary and
ensure they are closed properly after each opening.
What is not covered?
• Transit, delivery or accidental damage or misuse and abuse.
• Cabinet or appearance parts, including knobs, flaps, handles or container
lids.
4- Defrost frozen food in the fridge compartment, so that frozen food acts as an
ice pack to assist cooling in the fridge.
• Accessories or consumable items including but not limited to, ice trays, scrapers,
cutlery baskets, filters and light bulbs.
• Repairs required as a result of unauthorised repair or inexpert installation that
fails to meet the requirements contained in the user instruction book.
• Repairs to products used on commercial or non-residential household premises.
• Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is often
included within your household contents insurance policy, or may be available
separately from your retailer).
PROBLEM SOLVING
If the appliance does not operate when switched on, check whether:
• The plug is inserted properly in the socket and that the power supply is on. (To
check the power supply to the socket, plug in another appliance)
Important notes.
• Your Beko product is designed and built for domestic household use only.
• The guarantee will be void if the product is installed or used in commercial
or non-residential domestic household premises.
• The fuse has blown/circuit breaker has tripped/main distribution switch has
been turned off.
• The product must be correctly installed, located and operated in accordance
with the instructions contained in the User Instructions Booklet provided.
• Professional installation by a qualified Electrical Domestic Appliance Installer
is recommended for all Washing Machines, Dishwashers and Electric Cookers
• Gas Cookers must only be installed by a CORGI (or BORD GAIS) registered
Gas Installer.
• The temperature control has been set correctly.
• New plug is wired correctly if you have changed the fitted moulded plug.
If the appliance is still not operating after the above checks, please refer to the
section on “How To Obtain Service”.
• The guarantee is given only within the boundaries of the United Kingdom and
the Republic of Ireland.
Please ensure that above checks have been made as a charge will be made if no
fault is found.
• The guarantee is applicable only to new products and is not transferable if the
product is resold.
• Beko disclaims any liability for incidental or consequential damages.
The guarantee does not in anyway diminish your statutory or legal rights.
17
18
HOW TO OBTAIN SERVICE
Please keep your purchase receipt or other proof of purchase in a safe place;
you will need to have it should the product require attention under guarantee.
You should also complete the details below; it will help us assist you when requesting
service. (The model number is printed on the Instruction Booklet and the serial
number is printed on the Rating Label affixed to the appliance)
Model No:
Serial No:
Retailer:
Date of purchase:
For service under guarantee simply telephone the appropriate number below
UK Mainland & Northern Ireland
Fridges & Freezers
Electric Cookers
Gas & Dual Fuel Cookers
Washing Machines
& Dishwashers
0870 241 0638
0870 241 1320
0870 241 1321
0870 241 0357
Republic of Ireland
All Refrigeration, All Cookers
Washing Machines & Dishwashers
01 862 3411
Before requesting service please check the trouble-shooting guide in the Operating
Instructions as a charge may be levied where no fault is found even though your
product may still be under guarantee.
Service once the manufacturers guarantee has expired.
If you have purchased an extended guarantee please refer to the instructions
contained within the extended guarantee agreement document. Otherwise please
call the appropriate number above where service can be obtained at a charge.
Should you experience any difficulty in obtaining service please contact the Beko
Customer Help-Line.
19
|