ATON Stereo Receiver AIE2 User Manual

Installation  
Limited Warranty  
Typical Installation  
AIE2  
• Locate the component’s IR receiver window. Thoroughly clean this window to  
remove fingerprints, dust, etc.  
ATON* warrants to the purchaser/end user (“you”) that the AIE2 is to be free from defects in materials and  
workmanship for a period of five (5) years from date of purchase (the “Warranty Period”). This warranty is trans-  
ferable to subsequent owners of the product as long as the original proof of purchase is retained. If you discover  
a defect in material or workmanship within the Warranty Period, you can obtain warranty service by contacting  
ATON during the Warranty Period at (859)-422-7137 or [email protected]. If ATON determines that the  
product is in fact defective, ATON shall, at its option, repair or replace the product free of charge to you.  
This warranty shall not apply to equipment (a) not manufactured by ATON, (b) to equipment which was improperly  
installed, (c) which was repaired or altered by persons other than ATON or its authorized representatives or sub-  
ject to unauthorized tampering, alteration or modification, (d) damaged due to misuse, negligence, accident, acts  
of God (including, but not limited to, excess moisture, insects, lightning, flood, electrical surge, tornado, earth-  
quake, or other catastrophic events beyond ATON’s control), or (e) subject to improper operation, maintenance  
or storage or unreasonable use. The foregoing warranties do not cover reimbursement for labor, transportation,  
removal, installation or other expenses which may be incurred in connection with repair or replacement. The  
foregoing remedies shall be your exclusive remedies for any breach of warranty.  
• Peel the protective layer off of the adhesive strip on the docking station and apply  
to the IR receiver window.  
Talk Back IR  
Emitter  
• Orient the docking station vertically, then press down for several seconds to  
ensure good contact with the adhesive.  
AIR6  
In-Wall  
IR Receiver  
• Slide the emitter down from the top into the docking station. It should snap into  
place.  
• Connect the 3.5mm plug into an ATON DLA 2/4/6 Speaker Selector, AIB4  
Amplified IR Connection Block or other source of IR.  
• Remove the emitter from the docking station by sliding it upward.  
Introduction  
A/V Receiver  
Emitter &  
Docking Station  
White Stripe = +  
Connection  
Terminals  
3.5mm Mini-Plug  
Further, the foregoing warranty does not extend to equipment sold, but not manufactured by, ATON (“Third Party  
Products”). With respect to any Third Party Products, the warranty for such product shall be as provided by the  
manufacturer of such product, who will also be responsible for warranty service, and ATON will pass through to  
you any transferable warranty actually extended to ATON by the manufacturer.  
Attach Docking Station  
to IR Receiver Window  
w/Adhesive Strip  
7/16"  
AIE2 Talk-Back Emitter  
8 Feet  
9/16"  
Slide Emitter into  
Docking Station  
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED  
WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO  
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.  
Satellite  
Emitter  
1/4"  
Emitter Slides Into  
Docking Station  
Rear View  
Notwithstanding the above, where applicable, if you qualify as a “consumer” under the Magnuson-Moss Warranty  
Act, then you may be entitled to any implied warranties allowed by law for the Warranty Period. Some states do  
not allow limitations on how long an implied Limited Warranty lasts, so the above limitation may not apply to you.  
Adhesive  
Strip  
AIE2 Talk-Back Emitter  
Docking  
Station  
DVD  
ATTENTION: TO OUR VALUED CONSUMERS  
Valid proof of purchase is required for all warranty services. Warranty service requests made without proof  
of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to  
request warranty service.  
The ATON AIE2 is a sophisticated, detachable IR emitter. It features a docking  
station that permits temporary removal of the emitter for rearranging or servicing  
components. The AIE2 flashes red when emitting IR signals, making it an ideal  
troubleshooting tool. This unit has 75% lower IR output than non-visible emitters,  
therefore should not be used in “Blaster” applications.  
PS2  
Emitter Properly Installed  
Power  
Supply  
AIE2 Talk-Back Emitter  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
* ATON is a division of ELAN Home Systems, LLC.  
AIB4  
To 120V AC  
Amplified IR  
(unswitched)  
Connection Block  
Installation Notes:  
• Read the Owner’s Manual for the component to be controlled to find where the  
IR Receiver Window is located. A flashlight can also be useful for this purpose.  
• Emitters can be attached without the docking station. Use an extra adhesive  
strip (included) applied directly to the flat side of the emitter.  
• Use a new adhesive strip when re-attaching docking ports or emitters.  
• The outer shell of the AIE2 is transparent to IR so that hand-held remotes can  
be used even if the emitter is covering the component’s IR receiver.  
Caution:  
Do not plug the AIE2 into an emitter jack that is set to HIGH Power or “Blaster  
as this will damage the emitter.  
Installation Notes:  
• Read the Owner’s Manual for the component to be controlled to find where the  
IR receiver window is located. A flashlight can also be useful for this purpose.  
• Emitters can be attached without the docking station. Use an extra adhesive  
strip (included) applied directly to the flat side of the emitter.  
Additional Locations for Emitter Placement  
Since the AIE2 has high output from its curved surface, it may be attached to near-  
by surfaces such as shelves, doors, or cabinets. Use the LOW power  
setting (not blaster power) on the connection block.  
or  
• Use a new adhesive strip when re-attaching docking ports or emitters.  
• The outer shell of the AIE2 is transparent to IR so that hand-held remotes can  
be used even if the emitter is covering the component’s IR receiver.  
©2007 • All rights reserved.  
P/N 227935 REV:B  
 
1
2
3
4

3M Mouse EM 550GPL User Manual
Adder Technology Switch AV4DVI User Manual
Alpine Car Speaker PWE S8 User Manual
Aluratek Digital Photo Frame ADMPF007F User Manual
American Standard Outdoor Shower 1660201 User Manual
AOC Flat Panel Television L22H998 User Manual
AOSafety Respiratory Product Half Mask Respirator User Manual
AO Smith Water Heater HWB 399 User Manual
Balance Model Vehicle 10505 User Manual
Beko Freezer BZ 77F User Manual