Included
Hardware
Universal Washer
(Qty 8)
3” Lag Bolts
(Qty 6)
INSTALLATION GUIDE: XUF-3760
NOTE: To correctly determine your hardware, please refer
Victory Flat Screen Wall Mounting System
Flat Washers (Qty 6)
to the hardware list below.
The Victory Flat Screen Wall Mounting System is designed for secure installation of flat screen displays up
to 60”.
(Qty 8)
(Qty 6)
(Qty 6)
M4 x 16
M6 x 20
M6 x 30
9/16" Nylon spacers
(Qty 6)
1/4" Nylon spacers
(large)
(Qty 6)
(Qty 4)
M4 x 25
M5 x 12
(Qty 6)
(Qty 8)
Warning Statements
M8 x 20
(Qty 6)
M5 x 16
1/2" Nylon spacers
(large)
(Qty 12)
Nylon sleeves
(Qty 4)
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A
MINIMUM WEIGHT OF 350LBS. IF NOT, THE WALL MUST BE REINFORCED.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN,
AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO.
FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN
DEATH. DO NOT PLACE A UNIT WEIGHING MORE THAN 175LBS. ON THIS
UNIT.
WARNING:
(Qty 6)
(Qty 6)
M5 x 20
M5 x 25
M5 x 50
M8 x 25
M8 x 30
(Qty 4)
(Qty 6)
5/16" Flat washers
(metal)
(Qty 6)
(Qty 4)
M8 x 35
(Qty 4)
(Qty 8)
M6 x 12
1/4" Nylon spacers
(small)
(Qty 6)
M8 x 70
(Qty 4)
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS
FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING:
WARNING:
Tool List
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION
INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
Phillips Head Screw Driver
Electronic Stud Finder
½” Socket and Wrench
Portable Drill
Masonry Bit for Concrete Installation
1/4” Drill Bit for Wood Installations
Level (Commercially Available)
A secure structure must support the weight, or load, of the display. When mounting to a
wall that contains wooden studs, dead center of the wooden stud must be confirmed prior to
installation.
SECURE THE PLATE TO THE WALL
Do not install on a structure that is prone to vibration, movement or chance of impact.
Failure to do so could result in damage to the display and/or damage to the mounting
surface.
1. Begin by removing all pieces of the Wall Mounting System to ensure that you have all the necessary parts.
2. Instructions for mounting will vary slightly depending on your wall construction.
Wood Stud Mounting
1. For secure wood stud mounting, the wall plate must be
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of
direct heat energy. Failure to do so may result in damage to the display and could increase
the risk of fire.
Lag Bolt and Washer
mounted to two studs at least 16” apart.
2. Use a high-quality electronic stud finder (commercially
available) to locate two adjacent studs and mark their
locations with a pencil.
3. With the help of an assistant, use a level (commercially
available) and position the wall plate against the wall in
the desired mounting location.
At least two qualified people should perform the installation procedure. Injury and/or
damage can result from dropping or mishandling the display.
4. Mark the right, upper and lower and the left (upper
and lower), positions of the small horizontal slots
that are in alignment with the studs.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to
be installed on any surface other than wooden studs, use suitable hardware (which is
commercially available).
5. You should mark four positions total.
6. Next, pre-drill a 1/4” hole in the wall stud at each
marked location.
Contact V-Mounts with any technical / installation questions.
Continued on back page
9531-014-022-06
|